Tag Archives: magnet screw

China factory Two-Stage Compression High Efficiency Permanent Magnet Variable Speed Screw Air Compressor CT Series 37kw~132kw air compressor oil

Product Description

Product Presentation

CT Series Parameter Table
Model	C37T	C55T	C75T	T90PM	T110PM	T132PM
Rate Power	37kW	55kW	75kW	90kW	110kW	132kW
F.A.D	7.5m3/min	11.8m3/min	16.0m3/min	18.7m3/min	22.5m3/min	27.0m3/min
Pressure	≤0.8MPa (Please contact if there is any other pressure requirement,Under different pressure, the exhaust volume can be adjusted)
Drive Type	PM Motor/Direct-driven
Voltage/Frequency	AC380V-50Hz
Starting Mode	Variable Frequency
Connection	G1-1/2”	G1-1/2”	DN65	DN80	DN80	DN80
Size(LxWxH)	1520X1050X1500mm	1580X1160X1600mm	1700X1160X1720mm	2850X1840X2200mm
Weight	525kg	1085kg	1135kg	3000kg	3500kg	3800kg

Comparison between permanent magnet motor and ordinary asynchronous motor

Compared with electrically excited motors, permanent magnet motors have the following advantages:
High efficiency
Eliminate excitation system loss, improve efficiency 5-12%, high power factor, large torque inertia ratio, stator current and stator resistance loss reduction, and rotor parameters can be measured, good control performance, motor direct drive, no speed slip, no bearing and connection transmission, efficiency increased by more than 3%, light load than the same specification asynchronous motor efficiency increased by 15-35% or so. Always efficient regardless of light load or heavy load. At present, the energy efficiency of permanent magnet motors used by Hylein has reached the national level 1 energy efficiency standards.
Low noise
Reasonable magnetic field design, magnetic density distribution, wider operating frequency range, lower operating noise. Truly constant air pressure: open loop vector control, response time < 50ms, can adjust gas production in an instant over a wide range.
Compact structure, small size, light weight, high precision and fast response
The exciting winding and the exciting power supply (magnetic pole core) are eliminated, and the structure is simple, the operation is reliable and the maintenance is convenient.
High starting torque
The starting torque and overload capacity of permanent magnet synchronous motor are 1 power level higher than that of three-phase asynchronous motor, and the ratio of the maximum starting torque to the rated torque can reach more than 3 times, while the general asynchronous motor is only 1.6 times.

Two-stage Compression

Energy Efficient Save A Lot

Most enterprises reserve 20% of the air compressor displacement when selecting the type of air compressor because of the consideration of pressure loss and popular selection method.
The air consumption fluctuates greatly at different time periods every year, every month, and every day, which directly leads to the vast majority of the air compressor time consumption only between 50-70% of the rated air displacement, and the user spends unnecessary electricity.
The cost can not be reduced, in the current situation, the cost of materials is no longer the key to the cost of the product, but the electricity bill from day to month, saving electricity is saving cost, so that your products are more competitive!
Conclusion :Compared with ordinary power frequency and frequency conversion air compressor, permanent magnet frequency conversion air compressor has lower energy consumption and more energy saving!

Air-end Operates Almost Silent

Through the selection of advanced design structure, optimization of fluid and sound absorbing materials and other countermeasures, to achieve ultra-low operating sound.
The fan blade adopts frequency conversion control to further reduce noise (optional).
Full consideration of sound pressure, sound quality, volume noise countermeasures to minimize noise. Make it suitable for any occasion.

Quality Upgrade Three Lightspots

Company Profile

HangZhou Hylein Energy & Environmental Technology Co., Ltd. is located in HangZhou, Pearl River Delta, known as China’s compressor production base, is a professional engaged in all kinds of screw air compressor, nitrogen machine, oxygen generator, vacuum pump, magnetic suspension compressor R & D, production and sales of manufacturing enterprises, with standard production assembly line, the introduction of Europe and North America mature and experienced technology, Focus on providing a full range of services for various industries.
We strictly follow the IS09001 quality system standards and related industry standards, and throughout the product design, procurement, manufacturing, inspection, sales and service of the entire process, we always adhere to the global procurement strategy to ensure the superior performance of each air compressor, we pay attention to the development of new products, the latest energy-saving products are providing quality services for the global industrial energy-saving cause.
In the ZheJiang -ZheJiang Railway oxygen supply system air compressor project, we overcome high altitude, ultra-low temperature, ultra-high temperature, huge dust, frequent switching power supply and other problems.

After-sales Service

Equipment support High efficiency and energy saving equipment since the start of normal commissioning, to ensure the normal operation of the equipment.

Service scheme Monthly, quarterly regular arrangement of personnel to the user phone or on-site equipment operation inspection, testing work, timely understanding of unit operation dynamics, effective answer to user equipment operation questions, and do the corresponding need to improve maintenance, maintenance, to ensure the long-term effective work of the equipment, while providing service reports every time.

Technical service As long as the user needs equipment and technical help and consultation, the company will accurately reply within 2 hours, and provide the relevant technical information.

Service team We have a CHINAMFG theoretical knowledge, practical ability of strong service team and high-quality management team.

Corresponding time Our company will respond within 2 hours after receiving the notification of the failure of the user’s equipment, provide the fastest solution, and arrange technicians to arrive at the scene as soon as necessary.

Warranty commitment High efficiency and energy saving equipment since the start of normal commissioning, the whole machine warranty for 1 year.

FAQ

Q1: What’s your delivery time?

O: It takes about 15 days, if there is any urgent order, please contact us.

Q2: How long is your air compressor warranty?

O: One year for the whole machine when the compressor leave our factory.

Q3: How about your after-sales service?

O:1. Provide customers with installation and commissioning online instructions.

2. Well-trained engineers available to overseas service

/* January 22, 2571 19:08:37 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1

After-sales Service:	7*24
Warranty:	1 Year
Lubrication Style:	Lubricated
Cooling System:	Air Cooling
Power Source:	AC Power
Installation Type:	Stationary Type

Customization:	Available \|

air compressor

What are the advantages of using rotary vane compressors?

Rotary vane compressors offer several advantages that make them a popular choice for various applications. These compressors are widely used in industries where a reliable and efficient source of compressed air is required. Here are the advantages of using rotary vane compressors:

1. Compact and Lightweight:

Rotary vane compressors are typically compact and lightweight compared to other types of compressors. Their compact design makes them suitable for installations where space is limited, such as in small workshops or mobile applications. The lightweight nature of these compressors allows for easy transportation and maneuverability.

2. High Efficiency:

Rotary vane compressors are known for their high efficiency. The design of the vanes and the compression chamber allows for smooth and continuous compression, resulting in minimal energy losses. This efficiency translates into lower energy consumption and reduced operating costs over time.

3. Quiet Operation:

Rotary vane compressors operate with relatively low noise levels. The design of the compressor, including the use of vibration damping materials and sound insulation, helps to minimize noise and vibrations during operation. This makes rotary vane compressors suitable for applications where noise reduction is important, such as in indoor environments or noise-sensitive areas.

4. Oil Lubrication:

Many rotary vane compressors utilize oil lubrication, which provides several benefits. The oil lubrication helps to reduce wear and friction between the moving parts, resulting in extended compressor life and improved reliability. It also contributes to better sealing and improved efficiency by minimizing internal leakage.

5. Versatile Applications:

Rotary vane compressors are versatile and can be used in a wide range of applications. They are suitable for both industrial and commercial applications, including automotive workshops, small manufacturing facilities, dental offices, laboratories, and more. They can handle various compressed air requirements, from light-duty tasks to more demanding applications.

6. Easy Maintenance:

Maintenance of rotary vane compressors is relatively straightforward. Routine maintenance tasks typically include oil changes, filter replacements, and periodic inspection of vanes and seals. The simplicity of the design and the availability of replacement parts make maintenance and repairs easier and more cost-effective.

These advantages make rotary vane compressors an attractive choice for many applications, providing reliable and efficient compressed air solutions.

air compressor

How are air compressors employed in the mining industry?

Air compressors play a crucial role in the mining industry, providing reliable and efficient power for various mining operations. Here are some common applications of air compressors in mining:

1. Exploration and Drilling:

Air compressors are used during exploration and drilling activities in the mining industry. Compressed air is used to power drilling rigs, pneumatic hammers, and other drilling equipment. The high-pressure air generated by the compressor helps in drilling boreholes, extracting core samples, and exploring potential mineral deposits.

2. Ventilation and Air Quality Control:

Air compressors are employed in underground mining to provide ventilation and control air quality. Compressed air is used to operate ventilation fans and air circulation systems, ensuring adequate airflow and removing harmful gases, dust, and fumes from the mining tunnels and work areas.

3. Material Conveyance:

In mining operations, air compressors are used for material conveyance. Pneumatic systems powered by air compressors are utilized to transport materials such as coal, ore, and other minerals. Compressed air is used to operate pneumatic conveyors, pumps, and material handling equipment, allowing for efficient and controlled movement of bulk materials.

4. Dust Suppression:

Air compressors are employed for dust suppression in mining areas. Compressed air is used to spray water or other suppressants to control dust generated during mining activities. This helps in maintaining a safe and healthy work environment, reducing the risks associated with dust inhalation and improving visibility.

5. Instrumentation and Control:

Air compressors are used for instrumentation and control purposes in mining operations. Compressed air is utilized to power pneumatic control systems, control valves, and actuators. These systems regulate the flow of fluids, control equipment movements, and ensure the proper functioning of various mining processes.

6. Explosive Applications:

In mining, air compressors are used for explosive applications. Compressed air is employed to power pneumatic tools used for rock fragmentation, such as rock drills and pneumatic breakers. The controlled power of compressed air enables safe and efficient rock breaking without the need for traditional explosives.

7. Maintenance and Repair:

Air compressors are essential for maintenance and repair activities in the mining industry. Compressed air is used for cleaning machinery, removing debris, and powering pneumatic tools for equipment maintenance and repair tasks. The versatility and portability of air compressors make them valuable assets in maintaining mining equipment.

It is important to note that different mining operations may have specific requirements and considerations when selecting and using air compressors. The size, capacity, and features of air compressors can vary based on the specific mining application and environmental conditions.

By utilizing air compressors effectively, the mining industry can benefit from increased productivity, improved safety, and efficient operation of various mining processes.

air compressor

What is the purpose of an air compressor?

An air compressor serves the purpose of converting power, typically from an electric motor or an engine, into potential energy stored in compressed air. It achieves this by compressing and pressurizing air, which can then be used for various applications. Here’s a detailed explanation of the purpose of an air compressor:

1. Powering Pneumatic Tools: One of the primary uses of an air compressor is to power pneumatic tools. Compressed air can be used to operate a wide range of tools, such as impact wrenches, nail guns, paint sprayers, sanders, and drills. The compressed air provides the necessary force and energy to drive these tools, making them efficient and versatile.

2. Supplying Clean and Dry Air: Air compressors are often used to supply clean and dry compressed air for various industrial processes. Many manufacturing and production operations require a reliable source of compressed air that is free from moisture, oil, and other contaminants. Air compressors equipped with appropriate filters and dryers can deliver high-quality compressed air for applications such as instrumentation, control systems, and pneumatic machinery.

3. Inflating Tires and Sports Equipment: Air compressors are commonly used for inflating tires, whether it’s for vehicles, bicycles, or sports equipment. They provide a convenient and efficient method for quickly filling tires with the required pressure. Air compressors are also used for inflating sports balls, inflatable toys, and other similar items.

4. Operating HVAC Systems: Air compressors play a crucial role in the operation of heating, ventilation, and air conditioning (HVAC) systems. They provide compressed air for controlling and actuating dampers, valves, and actuators in HVAC systems, enabling precise regulation of air flow and temperature.

5. Assisting in Industrial Processes: Compressed air is utilized in various industrial processes. It can be used for air blow-off applications, cleaning and drying parts, powering air-operated machinery, and controlling pneumatic systems. Air compressors provide a reliable and efficient source of compressed air that can be tailored to meet the specific requirements of different industrial applications.

6. Supporting Scuba Diving and Breathing Systems: In scuba diving and other breathing systems, air compressors are responsible for filling diving tanks and supplying breathable air to divers. These compressors are designed to meet strict safety standards and deliver compressed air that is free from contaminants.

Overall, the purpose of an air compressor is to provide a versatile source of compressed air for powering tools, supplying clean air for various applications, inflating tires and sports equipment, supporting industrial processes, and facilitating breathing systems in specific contexts.

China factory Two-Stage Compression High Efficiency Permanent Magnet Variable Speed Screw Air Compressor CT Series 37kw~132kw air compressor oil
editor by CX 2024-05-22

China best High Efficiency Bmvf75 Permanent Magnet Screw Air Compressor with Tank air compressor CHINAMFG freight

Product Description

High Efficiency BMVF75 Permanent Magnet Screw Air Compressor with Tank

Oil injected screw air compressor has become the mainstream of air compressor development in the world. It has extremely superior and reliable performance. It has small vibration, low noise, high efficiency and few vulnerable parts. It has incomparable performance advantages of piston compressor (under the same exhaust pressure). The precise coordination between the male and female rotors and between the rotor and the main engine shell reduces the back- flow leakage and improves the efficiency; Only the rotors are meshed with each other, and reciprocating motion without cylinder, which reduces the source of vibration and noise; The unique lubrication method brings many advantages:

1. With the pressure difference generated by itself, lubricating oil is continuously injected into the compression chamber and bearing to simplify the complex mechanical structure.

2. The injected lubricating oil can form oil film between the rotors, and the primary can take secondary rotor to rotate, Without the help of high precision synchronous gear.

3. The injected lubricating oil can increase the air tightness.

4. The lubricating oil absorbs a lot of compression heat, so even if the compression ratio reaches 16, The head can still be controlled below the carbon deposition and degradation temperature of general lubricating oil, There is no friction between the rotor and the outside of the machine due to different expansion coefficient.

5. Lubricating oil reduces the noise caused by high frequency compression.

6. A small amount of oil into the compressed air, pneumatic tools have a certain lubrication.

Product Parameters

Screw group	5: 6 Gear rotor
Compression method	Continuous, CHINAMFG
Compressed air outlet pressure	0.65-1.0MPa
Compressed air outlet temperature	Air-cooled
Compressed air outlet temperature	10ºC~15ºC higher than the ambient temperature
Volume of Lubricating Oil	About 30liters
Motor speed	N=3000r/min
Rated power	75kw
Air capacity	V=10.5-13.1m3/min
Weight	1165kg
Upper air temperature	45ºC
Lower limit of air temperature	0ºC
Fuel consumption	Exhaust oil content is less than 3PPM
Noise level	80dB(A)
Dimensions (length×width×height) (mm)	1800x1190x1710

Detailed Photos

Wider range of speed regulation, higher accuracy of regulation, wider range of air supply pressure and higher energy efficiency.

The patented design of weak magnetic control, pressure control and simple and stable permanent magnet motor open-loop control can adapt to a variety of adverse working conditions and make the system more stable.

Motor and screw host coaxial, higher efficiency. The BMVF series is the CHINAMFG industry to achieve the screw host, synchronous motor, permanent magnet control electrical control synchronous design, and to achieve the advantages of cooperation.

Specification

Model	Working Pressure	Capacity	Motor Power	Connector	Weight	Noise	Dimension
Model	Bar	m³/min	kw	Connector	kg	dB(A)	mm
BMVF7.5G	0.65-1.0	1.0-1.25	7.5	G3/4	200	72	800510800
BMVF11G	0.65-1.0	1.5-1.85	11	G1	260	73	10006701090
BMVF15G	0.65-1.0	2.05-2.35	15		280	73	10006701090
BMVF22G	0.65-1.0	2.95-3.95	22		390	74	12008001120
BMVF37G	0.65-1.0	5.05-6.35	37		600	76	13408501300
BMVF45G	0.65-1.0	6.45-8.2	45		800	78	148010301365
BMVF55G	0.65-1.0	8.2-9.85	55		810	80	148010301365
BMVF75	0.65-1.0	10.5-13.1	75	G2	1280	81	180011901710
BMVF90	0.65-1.0	12.5-15.5	90	G2	1300	81	180011901710
BMVF110	0.65-0.8	22	110	DN65	1850	82	270012301730
BMVF132	0.65-0.8	24	132	DN65	2270	82	270012301730

Why Choose Us

CHINAMFG group is a state-level large scale enterprise headquartered in HangZhou, ZHangZhoug province, China. Over the last 60 years CHINAMFG Group has grown to become a significant diversified engineering company developing high value machinery for industry worldwide. CHINAMFG group is the largest rock drill manufacturer in the world, and the largest air compressor manufacturer in China. Exports are shipped to over 25 countries .Today we produce over 30 000 rotary screw and 250 000 reciprocating compressors annually.By the year of 2014 our sales amount was close to RMB 2 billion. CHINAMFG group also has the high-quality customer service system.
Our company is the authorized agent of CHINAMFG Group, specializing in air compressor, energy-saving transformation service and mining engineering construction machinery. We provide comprehensive technical support and after-sales service to customers.

CHINAMFG is headquartered in HangZhou in ZHangZhoug, China. It has subsidiaries in ZheJiang , Chgonqing, ZheJiang , ZheJiang , Hong Kong, Seattle, San Diego, Orlando, Melbourne, Singapore, Jakarta, Leobersdorf, Budapest and Belgrade, as well as offices in Russia, Colombia, Brazil, Korea, Malaysia and Thailand.

Advanced Equipment–Advanced equipment guarantees product quality. Over the years, we have received unanimous praise from overseas users for our integrity and high-quality product quality.

Packaging
The air compressor is guaranteed for 1 year. In addition to wearing parts and consumables, if the spare parts within the warranty period are broken, the company provides free spare parts replacement, but the buyer needs to pay the freight. Please ask customer service for specific warranty rules.

FAQ

Contacts

ZHangZhoug Stars Energy Saving Technology Co., Ltd.

If you want to know more information, please contact us!

/* January 22, 2571 19:08:37 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1

After-sales Service:	One Year Warranty
Warranty:	One Year
Lubrication Style:	Lubricated
Cooling System:	Air Cooling
Power Source:	AC Power
Cylinder Position:	Horizontal

Samples:	US$ 6080/Piece 1 Piece(Min.Order) \| Request Sample

Customization:	Available \|

air compressor

How are air compressors utilized in pharmaceutical manufacturing?

Air compressors play a crucial role in pharmaceutical manufacturing, where they are utilized for various critical applications. The pharmaceutical industry requires a reliable source of clean and compressed air to ensure the safety, efficiency, and quality of its processes. Here’s an overview of how air compressors are utilized in pharmaceutical manufacturing:

1. Manufacturing Processes:

Air compressors are used in numerous manufacturing processes within the pharmaceutical industry. Compressed air is employed for tasks such as mixing and blending of ingredients, granulation, tablet compression, coating, and encapsulation of pharmaceutical products. The controlled delivery of compressed air facilitates precise and consistent manufacturing processes, ensuring the production of high-quality pharmaceuticals.

2. Instrumentation and Control Systems:

Pharmaceutical manufacturing facilities rely on compressed air for powering instrumentation and control systems. Compressed air is used to operate pneumatic valves, actuators, and control devices that regulate the flow of fluids, control temperature and pressure, and automate various processes. The clean and dry nature of compressed air makes it ideal for maintaining the integrity and accuracy of these critical control mechanisms.

3. Packaging and Filling:

Air compressors are employed in pharmaceutical packaging and filling processes. Compressed air is used to power machinery and equipment for bottle cleaning, labeling, capping, and sealing of pharmaceutical products. Compressed air provides the necessary force and precision for efficient and reliable packaging, ensuring product safety and compliance.

4. Cleanroom Environments:

Pharmaceutical manufacturing often takes place in controlled cleanroom environments to prevent contamination and maintain product quality. Air compressors are used to supply clean and filtered compressed air to these cleanrooms, ensuring a controlled and sterile environment for the production of pharmaceuticals. Compressed air is also utilized in cleanroom air showers and air curtains for personnel and material decontamination.

5. Laboratory Applications:

In pharmaceutical laboratories, air compressors are utilized for various applications. Compressed air is used in laboratory instruments, such as gas chromatographs, mass spectrometers, and other analytical equipment. It is also employed in clean air cabinets, fume hoods, and laminar flow benches, providing a controlled and clean environment for testing, analysis, and research.

6. HVAC Systems:

Air compressors are involved in heating, ventilation, and air conditioning (HVAC) systems in pharmaceutical manufacturing facilities. Compressed air powers the operation of HVAC controls, dampers, actuators, and air handling units, ensuring proper air circulation, temperature control, and environmental conditions in various manufacturing areas.

By utilizing air compressors in pharmaceutical manufacturing, the industry can maintain strict quality standards, enhance operational efficiency, and ensure the safety and efficacy of pharmaceutical products.

air compressor

How are air compressors employed in the mining industry?

Air compressors play a crucial role in the mining industry, providing reliable and efficient power for various mining operations. Here are some common applications of air compressors in mining:

1. Exploration and Drilling:

2. Ventilation and Air Quality Control:

3. Material Conveyance:

4. Dust Suppression:

5. Instrumentation and Control:

6. Explosive Applications:

7. Maintenance and Repair:

By utilizing air compressors effectively, the mining industry can benefit from increased productivity, improved safety, and efficient operation of various mining processes.

air compressor

Can you explain the basics of air compressor terminology?

Understanding the basic terminology related to air compressors can help in better comprehension of their operation and discussions related to them. Here are some essential terms related to air compressors:

1. CFM (Cubic Feet per Minute): CFM is a unit of measurement that denotes the volumetric flow rate of compressed air. It indicates the amount of air a compressor can deliver within a minute and is a crucial factor in determining the compressor’s capacity.

2. PSI (Pounds per Square Inch): PSI is a unit of measurement used to quantify pressure. It represents the force exerted by the compressed air on a specific area. PSI is a vital specification for understanding the pressure capabilities of an air compressor and determining its suitability for various applications.

3. Duty Cycle: Duty cycle refers to the percentage of time an air compressor can operate in a given time period. It indicates the compressor’s ability to handle continuous operation without overheating or experiencing performance issues. For instance, a compressor with a 50% duty cycle can run for half the time in a given hour or cycle.

4. Horsepower (HP): Horsepower is a unit used to measure the power output of a compressor motor. It indicates the motor’s capacity to drive the compressor pump and is often used as a reference for comparing different compressor models.

5. Receiver Tank: The receiver tank, also known as an air tank, is a storage vessel that holds the compressed air delivered by the compressor. It helps in stabilizing pressure fluctuations, allowing for a more consistent supply of compressed air during peak demand periods.

6. Single-Stage vs. Two-Stage: These terms refer to the number of compression stages in a reciprocating air compressor. In a single-stage compressor, air is compressed in a single stroke of the piston, while in a two-stage compressor, it undergoes initial compression in one stage and further compression in a second stage, resulting in higher pressures.

7. Oil-Free vs. Oil-Lubricated: These terms describe the lubrication method used in air compressors. Oil-free compressors have internal components that do not require oil lubrication, making them suitable for applications where oil contamination is a concern. Oil-lubricated compressors use oil for lubrication, enhancing durability and performance but requiring regular oil changes and maintenance.

8. Pressure Switch: A pressure switch is an electrical component that automatically starts and stops the compressor motor based on the pre-set pressure levels. It helps maintain the desired pressure range in the receiver tank and protects the compressor from over-pressurization.

9. Regulator: A regulator is a device used to control and adjust the output pressure of the compressed air. It allows users to set the desired pressure level for specific applications and ensures a consistent and safe supply of compressed air.

These are some of the fundamental terms associated with air compressors. Familiarizing yourself with these terms will aid in understanding and effectively communicating about air compressors and their functionality.

China best High Efficiency Bmvf75 Permanent Magnet Screw Air Compressor with Tank air compressor CHINAMFG freight
editor by CX 2024-05-17

China Custom Best Sell 50HP/37kw Permanent Magnet Motor VSD Screw Rotary Air Compressor air compressor lowes

Product Description

ZheJiang Compressor Import & Export Co.,Ltd. is located in the logistics capital of China, 1 of the important
birthplaces of Chinese civilization-HangZhou, ZheJiang Province.
With professinal manufacturing experience and first -class comprehensive scientific and technological strength of the talent team, as the energy-saving compressor system leader and remowed in the industry.
We specializes in R & D and sales of power frequency ,permanent magnet frequency conversion ,two -stage compressor permanent magnet frequency conversion ,low -voltage and mobile screw air compressor . With a deep industry background , one step ahead ambition .
With the professional enthusiasm for screw air compressor , team innovation , to meat the challenges of enterprise’s
own determination and the rigorous attitude of excellence,products are strictly in accordance with IOS 9001 international quality procedures,to provide customers with energy -saving and reliable products .
We warmly welcomes people from all around the world to visit the company to guide the establishment of a wide range of business contacts and cooperation .
Choosing ZheJiang Compressor Import & Export Co.,Ltd.is to choose quality and service ,choose culture and taste ,choose a permanent and trustworthy partner !

RFQ:

Q1: Are you factory or trade company?
A1: We are factory. Please check Our Company Profile.

Q2: What the exactly address of your factory?
A2: Xihu (West Lake) Dis. Innovation Park, Zaoyuan Town, HangZhou, ZheJiang , China

Q3: Warranty terms of your machine?
A3: 18 months warranty for the machine,technical support according to your needs.

Q4: Will you provide some spare parts of the machines?
A4: Yes.

Q5: How long will you take to arrange production?
A5: Deliver standard goods within 30days, Other customized goods is TBD.

Q6: Can you accept OEM orders?
A6: Yes, with professional design team, OEM orders are highly welcome.

/* January 22, 2571 19:08:37 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1

Lubrication Style:	Oil-less
Cooling System:	Air Cooling
Power Source:	AC Power
Cylinder Position:	Horizontal
Structure Type:	Closed Type
Installation Type:	Stationary Type

Customization:	Available \|

air compressor

Can air compressors be used for cleaning and blowing dust?

Yes, air compressors can be effectively used for cleaning and blowing dust in various applications. Here’s how air compressors are utilized for these purposes:

1. Cleaning Machinery and Equipment:

Air compressors are commonly used for cleaning machinery and equipment in industries such as manufacturing, automotive, and construction. Compressed air is directed through a nozzle or blowgun attachment to blow away dust, debris, and other contaminants from surfaces, crevices, and hard-to-reach areas. The high-pressure air effectively dislodges and removes accumulated dust, helping to maintain equipment performance and cleanliness.

2. Dusting Surfaces:

Air compressors are also employed for dusting surfaces in various settings, including homes, offices, and workshops. The compressed air can be used to blow dust off furniture, shelves, electronic equipment, and other objects. It provides a quick and efficient method of dusting, especially for intricate or delicate items where traditional dusting methods may be challenging.

3. Cleaning HVAC Systems:

Air compressors are utilized for cleaning HVAC (Heating, Ventilation, and Air Conditioning) systems. The compressed air can be used to blow dust, dirt, and debris from air ducts, vents, and cooling coils. This helps improve the efficiency and air quality of HVAC systems, preventing the buildup of contaminants that can affect indoor air quality.

4. Blowing Dust in Workshops:

In workshops and garages, air compressors are often used to blow dust and debris from workbenches, power tools, and work areas. Compressed air is directed to blow away loose particles and maintain a clean and safe work environment. This is particularly useful in woodworking, metalworking, and other trades where dust and debris can accumulate during the manufacturing or fabrication processes.

5. Cleaning Electronics and Computer Equipment:

Air compressors are employed for cleaning electronics and computer equipment. The compressed air is used to blow dust and debris from keyboards, computer cases, circuit boards, and other electronic components. It helps in preventing overheating and maintaining the proper functioning of sensitive electronic devices.

6. Industrial Cleaning Applications:

Air compressors find extensive use in industrial cleaning applications. They are employed in industrial settings, such as factories and warehouses, for cleaning large surfaces, production lines, and equipment. Compressed air is directed through specialized cleaning attachments or air-operated cleaning systems to remove dust, dirt, and contaminants efficiently.

When using air compressors for cleaning and blowing dust, it is important to follow safety precautions and guidelines. The high-pressure air can cause injury if directed towards the body or sensitive equipment. It is advisable to wear appropriate personal protective equipment, such as safety glasses and gloves, and ensure that the air pressure is regulated to prevent excessive force.

Overall, air compressors provide a versatile and effective solution for cleaning and blowing dust in various applications, offering a convenient alternative to traditional cleaning methods.

air compressor

How do you choose the right air compressor for woodworking?

Choosing the right air compressor for woodworking is essential to ensure efficient and effective operation of pneumatic tools and equipment. Here are some factors to consider when selecting an air compressor for woodworking:

1. Required Air Volume (CFM):

Determine the required air volume or cubic feet per minute (CFM) for your woodworking tools and equipment. Different tools have varying CFM requirements, so it is crucial to choose an air compressor that can deliver the required CFM to power your tools effectively. Make sure to consider the highest CFM requirement among the tools you’ll be using simultaneously.

2. Tank Size:

Consider the tank size of the air compressor. A larger tank allows for more stored air, which can be beneficial when using tools that require short bursts of high air volume. It helps maintain a consistent air supply and reduces the frequency of the compressor cycling on and off. However, if you have tools with continuous high CFM demands, a larger tank may not be as critical.

3. Maximum Pressure (PSI):

Check the maximum pressure (PSI) rating of the air compressor. Woodworking tools typically operate within a specific PSI range, so ensure that the compressor can provide the required pressure. It is advisable to choose an air compressor with a higher maximum PSI rating to accommodate any future tool upgrades or changes in your woodworking needs.

4. Noise Level:

Consider the noise level of the air compressor, especially if you’ll be using it in a residential or shared workspace. Some air compressors have noise-reducing features or are designed to operate quietly, making them more suitable for woodworking environments where noise control is important.

5. Portability:

Assess the portability requirements of your woodworking projects. If you need to move the air compressor frequently or work in different locations, a portable and lightweight compressor may be preferable. However, if the compressor will remain stationary in a workshop, a larger, stationary model might be more suitable.

6. Power Source:

Determine the power source available in your woodworking workspace. Air compressors can be powered by electricity or gasoline engines. If electricity is readily available, an electric compressor may be more convenient and cost-effective. Gasoline-powered compressors offer greater flexibility for remote or outdoor woodworking projects where electricity may not be accessible.

7. Quality and Reliability:

Choose an air compressor from a reputable manufacturer known for producing reliable and high-quality equipment. Read customer reviews and consider the warranty and after-sales support offered by the manufacturer to ensure long-term satisfaction and reliability.

8. Budget:

Consider your budget and balance it with the features and specifications required for your woodworking needs. While it’s important to invest in a reliable and suitable air compressor, there are options available at various price points to accommodate different budgets.

By considering these factors and evaluating your specific woodworking requirements, you can choose an air compressor that meets the demands of your tools, provides efficient performance, and enhances your woodworking experience.

air compressor

How is air pressure measured in air compressors?

Air pressure in air compressors is typically measured using one of two common units: pounds per square inch (PSI) or bar. Here’s a brief explanation of how air pressure is measured in air compressors:

1. Pounds per Square Inch (PSI): PSI is the most widely used unit of pressure measurement in air compressors, especially in North America. It represents the force exerted by one pound of force over an area of one square inch. Air pressure gauges on air compressors often display pressure readings in PSI, allowing users to monitor and adjust the pressure accordingly.

2. Bar: Bar is another unit of pressure commonly used in air compressors, particularly in Europe and many other parts of the world. It is a metric unit of pressure equal to 100,000 pascals (Pa). Air compressors may have pressure gauges that display readings in bar, providing an alternative measurement option for users in those regions.

To measure air pressure in an air compressor, a pressure gauge is typically installed on the compressor’s outlet or receiver tank. The gauge is designed to measure the force exerted by the compressed air and display the reading in the specified unit, such as PSI or bar.

It’s important to note that the air pressure indicated on the gauge represents the pressure at a specific point in the air compressor system, typically at the outlet or tank. The actual pressure experienced at the point of use may vary due to factors such as pressure drop in the air lines or restrictions caused by fittings and tools.

When using an air compressor, it is essential to set the pressure to the appropriate level required for the specific application. Different tools and equipment have different pressure requirements, and exceeding the recommended pressure can lead to damage or unsafe operation. Most air compressors allow users to adjust the pressure output using a pressure regulator or similar control mechanism.

Regular monitoring of the air pressure in an air compressor is crucial to ensure optimal performance, efficiency, and safe operation. By understanding the units of measurement and using pressure gauges appropriately, users can maintain the desired air pressure levels in their air compressor systems.

China Custom Best Sell 50HP/37kw Permanent Magnet Motor VSD Screw Rotary Air Compressor air compressor lowes
editor by CX 2024-05-09

China Standard High Quality ASME 7.5kw/11kw/15kw/22kw and 8bar/10bar/15bar/16bar VSD Premanent Magnet High Pressure Electric AC All in One Industry Rotary Screw Air Compressor air compressor for sale

Product Description

Xihu (West Lake) Dis.nized man-machine interface display control system
• The operation is particularly convenient and simple, and the running status is clear at a glance.
• Can work for you 24 hours a day under unattended conditions.
• Once abnormal factors appear, maintenance or overhaul will be prompted in Chinese.
• Reserve output interface, which can realize chain control and remote diagnosis control of multiple units.
• Economical and easy to maintain, suitable for low-power hosts.
Low consumption and high efficiency motor
• High starting torque.
• Insulation class F, protection class IP23.
•Built-in refueling device, can refuel without stopping.
Efficient intake control valve
• NO/OFF control method.
• Anti-injection design with check valve.

Technical Parameters

Exhaust pressure(Mpa)	0.8MPa
Cooling method	Air-cooling
Compressed air outlet temperature	10ºC~15ºC higher than the ambient temperature
Motor power(KW)	15 kW
Exhaust volume(m³/min)	2.3
Weight	440 kg
Exhaust connection	G1
Dimension (length×width×height) (mm)	1110x850x1230

Product pictures
Built-in oil separation system The built-in oil separation design ensures the separation of oil and gas and reduces fuel consumption.

Certified Genuine Parts. CHINAMFG Certified Genuine Parts to ensure the compressors delivered to you always perform at high performance.

Adhering to the basic belief in environmental sustainability, we have been committed to continuously improving the energy efficiency of our
products and creating value for users.

Energy saving and economical, reliable and durable, environmentally friendly and quiet.

The latest generation of high-efficiency rotor profiles, full-spectrum screw mainframe meets the national energy-saving standards.

Product Parameters

Model	Exhaust pressure (Mpa)	Exhaust volume (m³/min)	Motor power (KW)	Exhaust connection	Weight (kg)	Dimension (mm)
LG7.5-8A	0.8	1.2	7.5	G1	260	820x700x1571
LG7.5-10A	1.0	1.0	7.5	G1	260	820x700x1571
LG7.5-13A	1.3	0.8	7.5	G1	260	820x700x1571
LG11-8	0.8	1.7	11	G1	420	1110x850x1230
LG11-10	1.0	1.5	11	G1	420	1110x850x1230
LG11-13	1.3	1.2	11	G1	420	1110x850x1230
LG15-8	0.8	2.3	15	G1	440	1110x850x1230
LG15-10	1.0	2.1	15	G1	440	1110x850x1230
LG15-13	1.3	1.6	15	G1	440	1110x850x1230
LG18-8GA	0.8	3.37	18.5	G1	510	1370x900x1110
LG22-8GA	0.8	4.2	22	G1	540	1370x900x1110
LG30-8GA	0.8	5.8	30	G11/2	650	1600x960x1220
LG37-8GA	0.8	7.0	37	G11/2	700	1600x960x1220
LG45-8GA	0.8	8.7	45	G11/2	880	1630x960x1220
LG55-8GA	0.8	10.5	55	G1V2	1090	1850x1200x1500
LG75-8GA	0.8	14.2	75	G2	1550	2160x1220x1580
LG75-10GA	1.0	11.6	75	G2	1550	2160x1220x1580
LG75-13GA	1.3	9.5	75	G2	1550	2160x1220x1580
LG90-8GA	0.8	17.2	90	G2	2000	2160x1320x1580
LG90-10GA	1.0	14.2	90	G2	2000	2160x1320x1580
LG90-13GA	1.3	11.6	90	G2	2000	2160x1320x1580
LG110-8GA	0.8	20.8	110	DN65	2700	2440x1400x1710

Company Information
Our Company–Worldwide Factories Make After-Sale Worry-free!
In 2009, CHINAMFG established Jersey North American Research Center in Seattle in the United States, attracting many top-notch compressor experts from around the world and creating a new model that is aptly described as “developed in America, Made in China”

Certifications

Global Customers–You are not alone!

Customer Cases

/* January 22, 2571 19:08:37 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1

After-sales Service:	One Year Warranty
Warranty:	One Year
Lubrication Style:	Lubricated
Cooling System:	Air Cooling
Power Source:	AC Power
Cylinder Position:	Horizontal

Customization:	Available \|

air compressor

Can air compressors be used for cleaning and blowing dust?

Yes, air compressors can be effectively used for cleaning and blowing dust in various applications. Here’s how air compressors are utilized for these purposes:

1. Cleaning Machinery and Equipment:

2. Dusting Surfaces:

3. Cleaning HVAC Systems:

4. Blowing Dust in Workshops:

5. Cleaning Electronics and Computer Equipment:

6. Industrial Cleaning Applications:

Overall, air compressors provide a versatile and effective solution for cleaning and blowing dust in various applications, offering a convenient alternative to traditional cleaning methods.

air compressor

How do you choose the right air compressor for woodworking?

1. Required Air Volume (CFM):

2. Tank Size:

3. Maximum Pressure (PSI):

4. Noise Level:

5. Portability:

6. Power Source:

7. Quality and Reliability:

8. Budget:

air compressor

Can air compressors be used for automotive applications?

Yes, air compressors can be used for various automotive applications and are commonly found in automotive repair shops, garages, and even in some vehicles. Here are some automotive applications where air compressors are frequently utilized:

1. Tire Inflation: Air compressors are commonly used to inflate tires in automotive applications. They provide a convenient and efficient way to inflate tires to the recommended pressure, ensuring optimal tire performance, fuel efficiency, and safety.

2. Air Tools: Air compressors power a wide range of pneumatic tools used in automotive repair and maintenance. These tools include impact wrenches, ratchet wrenches, air hammers, pneumatic drills, and sanders. Air-powered tools are favored for their high torque and power-to-weight ratio, making them suitable for heavy-duty automotive tasks.

3. Spray Painting: Air compressors are commonly used in automotive painting applications. They power airbrushes and spray guns that are used to apply paint, primer, and clear coats. Air compressors provide the necessary air pressure to atomize the paint and deliver a smooth and even finish.

4. Brake System Maintenance: Air compressors play a crucial role in maintaining and diagnosing automotive brake systems. They are used to pressurize the brake lines, allowing for proper bleeding of the system and detection of leaks or faults.

5. Suspension Systems: Some automotive suspension systems, such as air suspensions, rely on air compressors to maintain the desired air pressure in the suspension components. The compressor inflates or deflates the suspension as needed to provide a comfortable ride and optimal handling.

6. Cleaning and Dusting: Air compressors are used for cleaning automotive parts, blowing away dust and debris, and drying surfaces. They provide a high-pressure stream of air that effectively cleans hard-to-reach areas.

7. Air Conditioning Systems: Air compressors are a key component in automotive air conditioning systems. They compress and circulate refrigerant, allowing the system to cool and dehumidify the air inside the vehicle.

When using air compressors for automotive applications, it’s important to consider the specific requirements of the task at hand. Ensure that the air compressor has the necessary pressure and capacity to meet the demands of the application. Additionally, use appropriate air hoses, fittings, and tools that are compatible with the compressor’s output.

Overall, air compressors are versatile and valuable tools in the automotive industry, providing efficient power sources for a wide range of applications, from tire inflation to powering pneumatic tools and supporting various automotive systems.

China Standard High Quality ASME 7.5kw/11kw/15kw/22kw and 8bar/10bar/15bar/16bar VSD Premanent Magnet High Pressure Electric AC All in One Industry Rotary Screw Air Compressor air compressor for sale
editor by CX 2024-04-12

China Custom Pmsm Permanent Magnet Variable Frequency Drive VSD Screw Air Compressor with Hot selling

Product Description

Industrial Doulbe Permanent Magnet Synchronous Motor (PMSM) Variable Frequency Converter Drive Pm VSD Inverter Screw Air Compressor Advantage

01 Features Of permanent Magnet Variable Frequency Air Compressor

Ultra-low temperature rise design, which allows the compressor running at ultra-low frequency for a long time.
Closed-loop vector control system for faster control and more precise speed control.
The compressor unit can still operate efficiently when the frequency is reduced by more than 50%.
The pressure is stable and the pressure fluctuation is accurately controlled within 0.1 bar.
The figure shows a comparison of several starting methods. It can be seen that the frequency converter is slowly accelerated to start, the starting is more stable, and the current CHINAMFG is completely avoided.

02 Air End

More stable, no mechanical transmission failure: high-efficiency permanent magnet synchronous motor and screw male rotor adopt embedded-integrated shaft direct connection structure, no gear transmission, completely eliminate gear pitting or broken teeth; Two independent permanent magnet motors are integrated directly drive 2 air ends, no coupling failures.
More energy efficient, the air end is always running at energy-saving speed.
More efficient and efficient permanent magnet motor + no transmission efficiency loss.
More comfortable, low running noise, eliminating 3 sources of noise: no-click bearing noise, no gear meshing noise, no coupling drive noise.
More compact: The permanent magnet motor is small in size and the integrated structure saves space.
Under the set frequency conversion pressure, the unit will automatically adjust to keep the output pressure within ± 0.1 bar, reducing unnecessary waste (the power consumption increases by 7% for every 1 bar of pressure increase)

03 Advantages of Permanent Magnet Motors Compared to General Asynchronous Motors

High efficiency: Eliminates excitation system losses and improves efficiency.
It is still efficient under low load conditions: the energy efficiency of a permanent magnet motor is more than 9% higher than that of a conventional asynchronous motor at full load operation, and its energy efficiency remains unchanged as the speed decreases.
Large overdrive torque: The ratio of the maximum starting torque of the permanent magnet synchronous motor to the rated torque can be more than 3 times, while the general asynchronous motor is only 1.6 times.
The control is more stable: the corresponding time of the permanent magnet motor is <50ms, and the gas production can be adjusted in a large range in an instant, so that the gas pressure is truly stable.

04 Stainless Steel Piping Design

The piping arrangement is simple and beautiful. Stainless steel piping design to effectively prevent rust in the pipeline, and avoid safety accidents caused by leakage of the pipeline.

05 More Advanced Technology. More Powerful Inverter

The standard equipment is equipped with a high-frequency reactor to reduce the high frequency generated by the inverter.
The soft start of the inverter reduces the CHINAMFG current at startup, resulting in a smooth start and greatly reduced power costs.
Forced cooling of the inverter to prevent high temperature shutdown in Summer.
Standard equipment dust screen, circuit board surface coating treatment, high efficiency and durability against dirt, dust, moisture.
The special design of the heat dissipation area of the inverter ensures stable operation of the inverter under high temperature environment.
No idling occurs under any load conditions to achieve the desired power saving effect.
Quickly track changes in pressure, control pressure fluctuations within ±0.1 bar, and optimize the use of the power to accurately provide the right amount of air as needed

06 Oil Filter

The imported brand is used to reliably filter the dirt particles in the lubricating oil to ensure the smoothness and lubrication of the oil system at 0.1 micron.

07 Air Filter

The imported brand is used to reliably remove dirt from the air. The dust particles in the air are controlled below 0.3 microns and the filtration accuracy is as high as 99.99%.

Technical Parameters Of Variable Frequency Air Compressor with PMSM Motor

Model	Maximum working pressure		Capacity(FAD)		Installed motor power		IP Grade	Noise level	Dimensions (mm)			Weight	Air outlet pipe diameter	Starting Method	EEI

	bar(e)	psig	m3/min	cfm	kw	hp			(L)	(W)	(H)	kg
DAV-55+	7	102	6.46-12.93	228-457	55	75	IP54	75	191	200	270	IP54	85	3000	1950	2030	4700	DN100
	8	116	21.31-42.61	752-1505
	9	131	19.30-38.60	681-1363
10	145	17.85-35.71	630-1261
DAV-220+	7	102	24.14-48.28	852-1705	220	300	IP54	85	3500	2200	2300	5000	DN125
	8	116	23.91-47.82	844-1689
	9	131	22.89-45.79	808-1617
	10	145	20.42-40.83	721-1442
DAV-250+	7	102	28.24-56.48	997-1994	250	350	IP54	85	3500	2200	2300	5500	DN125
	8	116	26.54-53.08	937-1874
	9	131	25.45-50.89	899-1979
	10	145	23.00-46.00	812-1624
) FAD in accordance with ISO 1217:2009, Annex C: Ansolute intake pressure 1 bar (a), cooling and air intake temperature 20ºC *) Nosie level as per ISO 2151 and the basic standard ISO 9614-2, operation at maximum operating pressure and maximum speed; tolerance:±3 dB(A) Specifications are subject to change without prior notice

We carefully selected for you the classic case

14 sets of VSD air compressor for 40HQ are ready for packing and delivering to CHINAMFG distributor in Buenos Aires, Argentina. The compressors are high-end customized for Argentina market with Germany MANN filters, France SCHNEIDER inverter, Belgium CMC controller, etc.

DENAIR Facotry

DEANIR Customer

DENAIR Exhibitions

DENAIR Packing

FAQ

Q1: Are you factory or trade company?
A1: We are factory.

Q2: What the exactly address of your factory?
A2: Our company is located in No. 6767, Tingfeng Rd. Xihu (West Lake) Dis.n District, ZheJiang 201502, China
And our factory is located in No. 366, YangzhuangBang Street, Pingxing Rd., Xindai Town, HangZhou, ZHangZhoug Province, China

Q3: Warranty terms of your machine?
A3: Two years warranty for the machine and technical support according to your needs.

Q4: Will you provide some spare parts of the Air Compressors?
A4: Yes, of course.

Q5: How long will you take to arrange production?
A5: 380V 50HZ we can delivery the goods within 10 days. Other electricity or other color we will delivery within 22 days

Q6: Can you accept OEM orders?
A6: Yes, with professional design team, OEM orders are highly welcome. /* January 22, 2571 19:08:37 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1

Lubrication Style:	Lubricated
Cooling System:	Air Cooling
Cylinder Position:	Vertical

Customization:	Available \|

.shipping-cost-tm .tm-status-off{background: none;padding:0;color: #1470cc}

Shipping Cost: Estimated freight per unit.	about shipping cost and estimated delivery time.

Payment Method:
	Initial Payment Full Payment

Currency:	US$

Return&refunds:	You can apply for a refund up to 30 days after receipt of the products.

air compressor

Can air compressors be used for cleaning and blowing dust?

Yes, air compressors can be effectively used for cleaning and blowing dust in various applications. Here’s how air compressors are utilized for these purposes:

1. Cleaning Machinery and Equipment:

2. Dusting Surfaces:

3. Cleaning HVAC Systems:

4. Blowing Dust in Workshops:

5. Cleaning Electronics and Computer Equipment:

6. Industrial Cleaning Applications:

Overall, air compressors provide a versatile and effective solution for cleaning and blowing dust in various applications, offering a convenient alternative to traditional cleaning methods.

air compressor

How do you troubleshoot common air compressor problems?

Troubleshooting common air compressor problems can help identify and resolve issues that may affect the performance and functionality of the compressor. Here are some steps to troubleshoot common air compressor problems:

1. No Power:

Check the power source and ensure the compressor is properly plugged in.
Inspect the circuit breaker or fuse box to ensure it hasn’t tripped or blown.
Verify that the compressor’s power switch or control panel is turned on.

2. Low Air Pressure:

Check the air pressure gauge on the compressor. If the pressure is below the desired level, the compressor might not be building up enough pressure.
Inspect for air leaks in the system. Leaks can cause a drop in pressure. Listen for hissing sounds or use a soapy water solution to identify the location of leaks.
Ensure the compressor’s intake filter is clean and not clogged, as this can restrict airflow and reduce pressure.

3. Excessive Noise or Vibration:

Inspect the compressor’s mounting and foundation to ensure it is secure and stable. Loose mounts can cause excessive noise and vibration.
Check for loose or damaged components, such as belts, pulleys, or motor mounts. Tighten or replace as necessary.
Verify that the compressor’s cooling system, such as the fan or fins, is clean and free from obstructions. Overheating can lead to increased noise and vibration.

4. Air Leaks:

Inspect all connections, valves, fittings, and hoses for leaks. Tighten or replace any loose or damaged components.
Apply a soapy water solution to suspected areas and look for bubbles. Bubbles indicate air leaks.
Consider using thread sealant or Teflon tape on threaded connections to ensure a proper seal.

5. Excessive Moisture in Compressed Air:

Check the compressor’s drain valve and ensure it is functioning properly. Open the valve to release any accumulated moisture.
Inspect and clean the compressor’s moisture separator or air dryer, if equipped.
Consider installing additional filtration or drying equipment to remove moisture from the compressed air system.

6. Motor Overheating:

Ensure the compressor’s cooling system is clean and unobstructed.
Check the motor’s air intake vents and clean any dust or debris that may be blocking airflow.
Verify that the compressor is not being operated in an excessively hot environment.
Check the motor’s lubrication levels and ensure they are within the manufacturer’s recommended range.
Consider using a thermal overload protector to prevent the motor from overheating.

If troubleshooting these common problems does not resolve the issue, it may be necessary to consult the manufacturer’s manual or seek assistance from a qualified technician. Regular maintenance, such as cleaning, lubrication, and inspection, can also help prevent common problems and ensure the optimal performance of the air compressor.

air compressor

What maintenance is required for air compressors?

Maintaining air compressors is essential to ensure their optimal performance, longevity, and safe operation. Regular maintenance helps prevent breakdowns, improves efficiency, and reduces the risk of accidents. Here are some key maintenance tasks for air compressors:

1. Regular Inspection: Perform visual inspections of the air compressor to identify any signs of wear, damage, or leaks. Inspect the compressor, hoses, fittings, and connections for any abnormalities. Pay attention to oil leaks, loose bolts, and worn-out components.

2. Oil Changes: If your air compressor has an oil lubrication system, regular oil changes are crucial. Follow the manufacturer’s recommendations for the frequency of oil changes and use the recommended oil type. Dirty or degraded oil can impact compressor performance and lead to premature wear.

3. Air Filter Cleaning or Replacement: Clean or replace the air filter regularly to ensure proper air intake and prevent contaminants from entering the compressor. Clogged or dirty filters can restrict airflow and reduce efficiency.

4. Drain Moisture: Air compressors produce moisture as a byproduct of the compression process. Accumulated moisture in the tank can lead to rust and corrosion. Drain the moisture regularly from the tank to prevent damage. Some compressors have automatic drains, while others require manual draining.

5. Belt Inspection and Adjustment: If your compressor has a belt-driven system, inspect the belts for signs of wear, cracks, or tension issues. Adjust or replace the belts as necessary to maintain proper tension and power transmission.

6. Tank Inspection: Inspect the compressor tank for any signs of corrosion, dents, or structural issues. A damaged tank can be hazardous and should be repaired or replaced promptly.

7. Valve Maintenance: Check the safety valves, pressure relief valves, and other valves regularly to ensure they are functioning correctly. Test the valves periodically to verify their proper operation.

8. Motor and Electrical Components: Inspect the motor and electrical components for any signs of damage or overheating. Check electrical connections for tightness and ensure proper grounding.

9. Keep the Area Clean: Maintain a clean and debris-free area around the compressor. Remove any dirt, dust, or obstructions that can hinder the compressor’s performance or cause overheating.

10. Follow Manufacturer’s Guidelines: Always refer to the manufacturer’s manual for specific maintenance instructions and recommended service intervals for your air compressor model. They provide valuable information on maintenance tasks, lubrication requirements, and safety precautions.

Regular maintenance is vital to keep your air compressor in optimal condition and extend its lifespan. It’s also important to note that maintenance requirements may vary depending on the type, size, and usage of the compressor. By following a comprehensive maintenance routine, you can ensure the reliable operation of your air compressor and maximize its efficiency and longevity.

China Custom Pmsm Permanent Magnet Variable Frequency Drive VSD Screw Air Compressor with Hot selling
editor by CX 2024-03-29

China supplier Top Performance Stationary Low Noise Permanent Magnet Synchronous Variable Speed Driven VSD VFD 6~61 M3/Min 5bar Two-Stage Rotary Screw Type Air Compressor air compressor portable

Product Description

Top Performance Stationary Low Noise Permanent Magnet Synchronous Variable Speed Driven VSD VFD 6~61 m3/min 5bar Two-Stage Rotary Screw Type Air Compressor

Product Parameters

Technical Parameters Of fixed speed screw air compressor:

Model	Power (kw)	Air folw/pressure (m3/Bar)	Outlet size	Noise	Unit weight (KG)	Unit size (mm)
WZS-22PMD-2S	22	6.25m³/5Bar	RP1 1/2	66±3	1350	1800x1270x1550
WZS-30PMD-2S	30	7.2m³/5Bar	RP1 1/2	66±3	1550	1800x1270x1550
WZS-37PMD-2S	37	10m³/5Bar	RP1 1/2	68±3	1900	1800x1270x1550
WZS-45PMD-2S	45	12m³/5Bar	RP2	68±3	2100	1800x1270x1550
WZS-55PMD-2S	55	13.8m³/5Bar	RP2	70±3	2200	2100x1360x1660
WZS-75PMD-2S	75	18.5m³/5Bar	DN65	70±3	2800	2800x1750x1900
WZS-90PMD-2S	90	23m³/5Bar	DN65	72±3	2800	2800x1750x1900
WZS-110PMD-2S	110	28m³/5Bar	DN80	72±3	3200	3200x1750x2250
WZS-132PMD-2S	132	32.5m³/5Bar	D270N80	72±3	3500	3200x1750x2250
WZS-160PMD-2S	160	41m³/5Bar	DN125	74±3	4100	3200x1750x2350
WZS-185PMD-2S	185	45m³/5Bar	DN125	74±3	4500	3800x2150x2250
WZS-200PMD-2S	200	50m³/5Bar	DN150	76±3	5100	3800x2150x2250
WZS-220PMD-2S	220	54m³/5Bar	DN150	76±3	6200	3800x2250x2250
WZS-250PMD-2S	250	61m³/5Bar	DN150	78±3	6600	4200x2250x2400

Company Profile

Certifications

Exhibition

Before quotation:
1.Before quoting, what should users offer?
1).Discharge pressure (Bar, Mpa or Psi)
2).Air discharge/Air flow/Air capacity (m3/min or CFM)
3).Power supply (220/380V, 50/60Hz, 3Phase)

2.If I don’t know the pressure and air flow, what should I do?
1).Take the picture of nameplate, we will advise the suitable air compressor to you.
2).Tell us what industry you are, we can advise the suitable 1 (so as to air tank / air dryer / air filters).

High Efficiency PM Motor and Energy Saving
*With the high-performance permanent magnet material, PM motor won’t lose magnetism even under 120°c and can run for more than 15 years.
*No motor bearing: permanent magnet rotors is installed directly on the stretch out shaft of Male rotor. This structure doesn’t have the bearing and eliminates the motor bearing fault.
*Comparing to normal variable speed motor, the permanent magnet synchronous motor performs with even better energy efficiency. Especially in the low-speed condition, it can still maintain a high motor efficiency.

SHIPPING
Delivery: time 5-25 working days after payment receipt confirmed(based on actual quantity)
packing:standard export packing. or customized packing as your
Professional: goods shipping forwarder.

FAQ

Q: OEM/ODM, or customers logo printed is available?
Yes, OEM/ODM, customers logo is welcomed.

Q: Delivery date?
Usually 5-25 workdays after receiving deposit, specific delivery date based on order quantity

Q: what’s your payment terms?
Regularly doing 30% deposit and 70% balance by T/T, Western Union, Paypal, other payment terms also can be discussed based on our cooperation.

Q: How to control your quality?
We have professional QC team, control the quality during the mass production and inspect completely goods before shipping.

Q: If we don’t have shipping forwarder in China, would you do this for us?
We can offer you best shipping line to ensure you can get the goods timely at best price.

Q: come to China before, can you be my guide in China?
We are happy to provide you orservice, such as booking ticket, pick up at the airport, booking hotel, accompany visiting market or factory

/* January 22, 2571 19:08:37 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1

After-sales Service:	Video Technical Support
Warranty:	Unit 1 Year, Air End 2 Years
Lubrication Style:	Oil-less

Customization:	Available \|

.shipping-cost-tm .tm-status-off{background: none;padding:0;color: #1470cc}

Shipping Cost: Estimated freight per unit.	about shipping cost and estimated delivery time.

Payment Method:
	Initial Payment Full Payment

Currency:	US$

Return&refunds:	You can apply for a refund up to 30 days after receipt of the products.

air compressor

How are air compressors employed in the petrochemical industry?

Air compressors play a vital role in the petrochemical industry, where they are employed for various applications that require compressed air. The petrochemical industry encompasses the production of chemicals and products derived from petroleum and natural gas. Here’s an overview of how air compressors are utilized in the petrochemical industry:

1. Instrumentation and Control Systems:

Air compressors are used to power pneumatic instrumentation and control systems in petrochemical plants. These systems rely on compressed air to operate control valves, actuators, and other pneumatic devices that regulate processes such as flow control, pressure control, and temperature control. Compressed air provides a reliable and clean source of energy for these critical control mechanisms.

2. Pneumatic Tools and Equipment:

Petrochemical plants often utilize pneumatic tools and equipment for various tasks such as maintenance, repair, and construction activities. Air compressors supply the necessary compressed air to power these tools, including pneumatic drills, impact wrenches, grinders, sanders, and painting equipment. The versatility and convenience of compressed air make it an ideal energy source for a wide range of pneumatic tools used in the industry.

3. Process Air and Gas Supply:

Petrochemical processes often require a supply of compressed air and gases for specific applications. Air compressors are employed to generate compressed air for processes such as oxidation, combustion, and aeration. They may also be used to compress gases like nitrogen, hydrogen, and oxygen, which are utilized in various petrochemical reactions and treatment processes.

4. Cooling and Ventilation:

Petrochemical plants require adequate cooling and ventilation systems to maintain optimal operating conditions and ensure the safety of personnel. Air compressors are used to power cooling fans, blowers, and air circulation systems that help maintain the desired temperature, remove heat generated by equipment, and provide ventilation in critical areas.

5. Nitrogen Generation:

Nitrogen is widely used in the petrochemical industry for applications such as blanketing, purging, and inerting. Air compressors are utilized in nitrogen generation systems, where they compress atmospheric air, which is then passed through a nitrogen separation process to produce high-purity nitrogen gas. This nitrogen is used for various purposes, including preventing the formation of explosive mixtures, protecting sensitive equipment, and maintaining the integrity of stored products.

6. Instrument Air:

Instrument air is essential for operating pneumatic instruments, analyzers, and control devices throughout the petrochemical plant. Air compressors supply compressed air that is treated and conditioned to meet the stringent requirements of instrument air quality standards. Instrument air is used for tasks such as pneumatic conveying, pneumatic actuators, and calibration of instruments.

By employing air compressors in the petrochemical industry, operators can ensure reliable and efficient operation of pneumatic systems, power various tools and equipment, support critical processes, and maintain safe and controlled environments.

air compressor

What are the environmental considerations when using air compressors?

When using air compressors, there are several environmental considerations to keep in mind. Here’s an in-depth look at some of the key factors:

Energy Efficiency:

Energy efficiency is a crucial environmental consideration when using air compressors. Compressing air requires a significant amount of energy, and inefficient compressors can consume excessive power, leading to higher energy consumption and increased greenhouse gas emissions. It is important to choose energy-efficient air compressors that incorporate features such as Variable Speed Drive (VSD) technology and efficient motor design, as they can help minimize energy waste and reduce the carbon footprint.

Air Leakage:

Air leakage is a common issue in compressed air systems and can contribute to energy waste and environmental impact. Leaks in the system result in the continuous release of compressed air, requiring the compressor to work harder and consume more energy to maintain the desired pressure. Regular inspection and maintenance of the compressed air system to detect and repair leaks can help reduce air loss and improve overall energy efficiency.

Noise Pollution:

Air compressors can generate significant noise levels during operation, which can contribute to noise pollution. Prolonged exposure to high noise levels can have detrimental effects on human health and well-being and can also impact the surrounding environment and wildlife. It is important to consider noise reduction measures such as sound insulation, proper equipment placement, and using quieter compressor models to mitigate the impact of noise pollution.

Emissions:

While air compressors do not directly emit pollutants, the electricity or fuel used to power them can have an environmental impact. If the electricity is generated from fossil fuels, the associated emissions from power plants contribute to air pollution and greenhouse gas emissions. Choosing energy sources with lower emissions, such as renewable energy, can help reduce the environmental impact of operating air compressors.

Proper Waste Management:

Proper waste management is essential when using air compressors. This includes the appropriate disposal of compressor lubricants, filters, and other maintenance-related materials. It is important to follow local regulations and guidelines for waste disposal to prevent contamination of soil, water, or air and minimize the environmental impact.

Sustainable Practices:

Adopting sustainable practices can further reduce the environmental impact of using air compressors. This can include implementing preventive maintenance programs to optimize performance, reducing idle time, and promoting responsible use of compressed air by avoiding overpressurization and optimizing system design.

By considering these environmental factors and taking appropriate measures, it is possible to minimize the environmental impact associated with the use of air compressors. Choosing energy-efficient models, addressing air leaks, managing waste properly, and adopting sustainable practices can contribute to a more environmentally friendly operation.

air compressor

How do you choose the right size of air compressor for your needs?

Choosing the right size of air compressor is essential to ensure optimal performance and efficiency for your specific needs. Here are some factors to consider when selecting the appropriate size:

1. Air Demand: Determine the air demand requirements of your applications. Calculate the total CFM (Cubic Feet per Minute) needed by considering the air consumption of all the pneumatic tools and equipment that will be operated simultaneously. Choose an air compressor with a CFM rating that meets or exceeds this total demand.

2. Pressure Requirements: Consider the required operating pressure for your applications. Check the PSI (Pounds per Square Inch) rating of the tools and equipment you will be using. Ensure that the air compressor you choose can deliver the necessary pressure consistently.

3. Duty Cycle: Evaluate the duty cycle of the air compressor. The duty cycle represents the percentage of time the compressor can operate within a given time period without overheating or experiencing performance issues. If you require continuous or heavy-duty operation, choose a compressor with a higher duty cycle.

4. Power Source: Determine the available power source at your location. Air compressors can be powered by electricity or gasoline engines. Ensure that the chosen compressor matches the available power supply and consider factors such as voltage, phase, and fuel requirements.

5. Portability: Assess the portability requirements of your applications. If you need to move the air compressor frequently or use it in different locations, consider a portable or wheeled compressor that is easy to transport.

6. Space and Noise Constraints: Consider the available space for installation and the noise restrictions in your working environment. Choose an air compressor that fits within the allocated space and meets any noise regulations or requirements.

7. Future Expansion: Anticipate any potential future expansions or increases in air demand. If you expect your air demand to grow over time, it may be wise to choose a slightly larger compressor to accommodate future needs and avoid the need for premature replacement.

8. Budget: Consider your budgetary constraints. Compare the prices of different air compressor models while ensuring that the chosen compressor meets your specific requirements. Keep in mind that investing in a higher-quality compressor may result in better performance, durability, and long-term cost savings.

By considering these factors and evaluating your specific needs, you can choose the right size of air compressor that will meet your air demand, pressure requirements, and operational preferences, ultimately ensuring efficient and reliable performance.

China supplier Top Performance Stationary Low Noise Permanent Magnet Synchronous Variable Speed Driven VSD VFD 6~61 M3/Min 5bar Two-Stage Rotary Screw Type Air Compressor air compressor portable
editor by CX 2024-03-28

China factory 7.5kw 15kw 22kw IP23 Energy Saving Inverter Screw Air Compressor Stable Quality Rotary Type Air Compressor Integrated Permanent Magnet wholesaler

Product Description

Q1: What information do I need to provide to get the suitable machine?
1. How much air delivery capacity ( Unit:CFM or M3/Min )
2 How much working pressure ( Unit:PSI, Bar or Mpa )
3.What is the voltage and frequency of my country of residence ( V/Hz )
4. Whether I need other accessories such as air tank, filters and/or air dryers.
Tell us the answer, we will offer scheme for you!

Q2: What are the general unit conversion?
1bar = 0.1Mpa = 14.5psi 1m³/min = 35.32cfm 1KW = 1.34HP

Q3: Are you factory or trading company?
We are factory. Our factory is located in 39 Xihu (West Lake) Dis. Rd, HangZhou, ZHangZhoug

Q4: Which trade term can you accept?
FOB, CIF, CFR, EXW, etc.

Q5: How long will you take to arrange production?
15 days for Regular Products, 35 days for Customizing Models

SPECIFICATION

MODEL	LB-30-8
Ambient Temperature	-5ºC to +45 ºC
Max Pressure (bar)	8
Air Delivery (m3/min)	3.6
Compression Stage	Single Stage Compression
Cooling Method	Air Cooled
Discharge Temperature (ºC)	≤ 75ºC
Oil Cotent (ppm)	≤3
Transmission Method	Direct Drive(Non-Coupling)
Sound Level dB(A)	68±3
Lubricating Oil Amount	12.5L
Motor Power	22KW/30HP
Motor Level Of Protection	IP55
Voltage	380V/3ph/50Hz
Dimensions (mm)	1060×790×1160(LWH)
Weight	450KG
Discharge Outlet Thread	1”

After-sales Service:	Video, Live, Site Support
Warranty:	2-Year-Warranty
Lubrication Style:	Lubricated
Cooling System:	Air Cooling
Power Source:	AC Power
Installation Type:	Stationary Type

Samples:	US$ 980/set 1 set(Min.Order) \| Request Sample

Customization:	Available \|

air compressor

What are the advantages of using rotary vane compressors?

1. Compact and Lightweight:

2. High Efficiency:

3. Quiet Operation:

4. Oil Lubrication:

5. Versatile Applications:

6. Easy Maintenance:

These advantages make rotary vane compressors an attractive choice for many applications, providing reliable and efficient compressed air solutions.

air compressor

How are air compressors used in refrigeration and HVAC systems?

Air compressors play a vital role in refrigeration and HVAC (Heating, Ventilation, and Air Conditioning) systems, providing the necessary compression of refrigerant gases and facilitating the heat transfer process. Here are the key ways in which air compressors are used in refrigeration and HVAC systems:

1. Refrigerant Compression:

In refrigeration systems, air compressors are used to compress the refrigerant gas, raising its pressure and temperature. This compressed gas then moves through the system, where it undergoes phase changes and heat exchange to enable cooling or heating. The compressor is the heart of the refrigeration cycle, as it pressurizes and circulates the refrigerant.

2. Refrigeration Cycle:

The compression of refrigerant gas by the air compressor is an essential step in the refrigeration cycle. After compression, the high-pressure, high-temperature gas flows to the condenser, where it releases heat and condenses into a liquid. The liquid refrigerant then passes through an expansion valve or device, which reduces its pressure and temperature. This low-pressure, low-temperature refrigerant then enters the evaporator, absorbing heat from the surrounding environment and evaporating back into a gas. The cycle continues as the gas returns to the compressor for re-compression.

3. HVAC Cooling and Heating:

In HVAC systems, air compressors are used to facilitate cooling and heating processes. The compressor compresses the refrigerant gas, which allows it to absorb heat from the indoor environment in the cooling mode. The compressed gas releases heat in the outdoor condenser unit and then circulates back to the compressor to repeat the cycle. In the heating mode, the compressor reverses the refrigeration cycle, absorbing heat from the outdoor air or ground source and transferring it indoors.

4. Air Conditioning:

Air compressors are an integral part of air conditioning systems, which are a subset of HVAC systems. Compressed refrigerant gases are used to cool and dehumidify the air in residential, commercial, and industrial buildings. The compressor pressurizes the refrigerant, initiating the cooling cycle that removes heat from the indoor air and releases it outside.

5. Compressor Types:

Refrigeration and HVAC systems utilize different types of air compressors. Reciprocating compressors, rotary screw compressors, and scroll compressors are commonly used in these applications. The selection of the compressor type depends on factors such as system size, capacity requirements, efficiency, and application-specific considerations.

6. Energy Efficiency:

Efficient operation of air compressors is crucial for refrigeration and HVAC systems. Energy-efficient compressors help minimize power consumption and reduce operating costs. Additionally, proper compressor sizing and system design contribute to the overall energy efficiency of refrigeration and HVAC systems.

By effectively compressing refrigerant gases and facilitating the heat transfer process, air compressors enable the cooling and heating functions in refrigeration and HVAC systems, ensuring comfortable indoor environments and efficient temperature control.

air compressor

What is the difference between a piston and rotary screw compressor?

Piston compressors and rotary screw compressors are two common types of air compressors with distinct differences in their design and operation. Here’s a detailed explanation of the differences between these two compressor types:

1. Operating Principle:

Piston Compressors: Piston compressors, also known as reciprocating compressors, use one or more pistons driven by a crankshaft to compress air. The piston moves up and down within a cylinder, creating a vacuum during the intake stroke and compressing the air during the compression stroke.
Rotary Screw Compressors: Rotary screw compressors utilize two intermeshing screws (rotors) to compress air. As the male and female screws rotate, the air is trapped between them and gradually compressed as it moves along the screw threads.

2. Compression Method:

Piston Compressors: Piston compressors achieve compression through a positive displacement process. The air is drawn into the cylinder and compressed as the piston moves back and forth. The compression is intermittent, occurring in discrete cycles.
Rotary Screw Compressors: Rotary screw compressors also employ a positive displacement method. The compression is continuous as the rotating screws create a continuous flow of air and compress it gradually as it moves along the screw threads.

3. Efficiency:

Piston Compressors: Piston compressors are known for their high efficiency at lower flow rates and higher pressures. They are well-suited for applications that require intermittent or variable air demand.
Rotary Screw Compressors: Rotary screw compressors are highly efficient for continuous operation and are designed to handle higher flow rates. They are often used in applications with a constant or steady air demand.

4. Noise Level:

Piston Compressors: Piston compressors tend to generate more noise during operation due to the reciprocating motion of the pistons and valves.
Rotary Screw Compressors: Rotary screw compressors are generally quieter in operation compared to piston compressors. The smooth rotation of the screws contributes to reduced noise levels.

5. Maintenance:

Piston Compressors: Piston compressors typically require more frequent maintenance due to the higher number of moving parts, such as pistons, valves, and rings.
Rotary Screw Compressors: Rotary screw compressors have fewer moving parts, resulting in lower maintenance requirements. They often have longer service intervals and can operate continuously for extended periods without significant maintenance.

6. Size and Portability:

Piston Compressors: Piston compressors are available in both smaller portable models and larger stationary units. Portable piston compressors are commonly used in construction, automotive, and DIY applications.
Rotary Screw Compressors: Rotary screw compressors are typically larger and more suitable for stationary installations in industrial and commercial settings. They are less commonly used in portable applications.

These are some of the key differences between piston compressors and rotary screw compressors. The choice between the two depends on factors such as required flow rate, pressure, duty cycle, efficiency, noise level, maintenance needs, and specific application requirements.

China factory 7.5kw 15kw 22kw IP23 Energy Saving Inverter Screw Air Compressor Stable Quality Rotary Type Air Compressor Integrated Permanent Magnet wholesaler
editor by CX 2023-11-13

China Custom CHINAMFG (BOREAS) Bk Series Permanent Magnet Variable Frequency Screw Air Compressor manufacturer

Product Description

Short Description:

BK series new screw air compressor new-generation low-consumption and high-efficiency motor
Large starting torque, insulation class F, protection class IP54;
SKF bearings, low noise and long life;
With a refueling device, it can be refueled without stopping.

Scope of application:Electric power, petroleum, auto repair, laser equipment, metallurgy, biopharmaceutical, printing, garment industry

Product Description

Yin-Yang Rotor Compression System
Better sealing, smaller leakage channel will produce high-efficiency roller sliding film to reduce heat of compression, and gas production is improved by 10%-15%

Built-in oil and gas separation design
Adopt a built-in oil separation setting to ensure the oil and gas separation effect and reduce fuel consumption
·High filtration level and low flow resistance
·Good noise reduction and mute effect
· Oil and gas separation, high-temperature resistance, high-pressure resistance – reduce the oil content of the exhaust
·Clean exhaust to ensure clean gas

Timely Smart Control Panel
·Using a user-friendly interface to prompt operation, clear at a glance, real-time monitoring of information, providing important information alarm, storage, and query functions

Precision oil filter
·Use high-density filter paper to filter oil
· Completely filter out lubricating oil

Low-consumption and high-efficiency motor, large starting torque
·Insulation class F, protection class IP23.
·Built-in refueling device, can refuel without stopping.

Cooling copper pipe
The radiator made of high-quality copper tubes can make the heat generated by the condensation of the machine quickly Dissipate, maintain the internal temperature

oil pipeline
·Excellent material
·Stable oil delivery without clogging

The system adopts the step-less adjustment of the displacement of 0-100. When the air consumption is reduced, the exhaust volume is also reduced, and the current of the motor is also reduced at the same time; when the air is not used, the air compressor runs empty, and the air compressor is automatically stopped for a long time. When the gas consumption increases, resume the heavy vehicle. Excellent energy-saving effect.
good environmental adaptability
The extraordinary cooling system design is especially suitable for Asia’s high temperature and high humidity environments. The excellent vibration isolation technology and noise reduction measures make the installation of CHINAMFG screw air compressors not require special foundations. As long as a small space for ventilation and maintenance is left, your compressor can be installed well.
Design features of screw rotor profile:
1. Fully realize “surface-to-surface” meshing, thereby helping to form a hydrodynamic lubricating film, reducing lateral leakage through the contact belt, improving compressor efficiency; and improving rotor processing and inspection performance.
2. Adopt the design idea of “large rotor, large bearing, low speed”, the speed is 3050 lower than other brands, which can reduce noise and vibration, reduce exhaust temperature, improve rotor rigidity, prolong service life, and reduce the carbonization of impurities and oil animal sensitivity.
3. The power range is 4355KW, of which 18.5250KW are directly connected without a gearbox, 200KW and 250KW are directly connected with 4-pole motors, and the speed is as low as 1480 rpm

Product Parameters

Model	Working Pressure	Displacement	Motor Power	Exhaust interface	Weight	Noise	Dimension
	Bar	m³/min	kw		kg	dB(A)	mm
BK7.5-8G	8	1.2	7.5	G1	200	70	800620800
BK7.5-10	10	1	7.5	G3/4	200	72	7207001000
BK7.5-13	13	0.8	7.5	G3/4	200	72	7207001000
BK11-8G	8	1.7	11	G1	300	72	10006701090
BK11-10	10	1.5	11	G1	290	72	7006701250
BK11-13	13	1.2	11	G1	290	72	7006701250
BK15-8G	8	2.4	15	G1	280	73	10006701090
BK15-10	10	2.2	15	G1	290	73	7006701250
BK15-13	13	1.7	15	G1	290	73	7006701250
BK18-8	8	3	18.5	G1	500	74	10808801235
BK18-10	10	2.7	18.5	G1	500	74	10808801235
BK18-13	13	2.3	18.5	G1	500	74	10808801235
BK22-8ZG	8	3.6	22	G1	380	74	*12008001100*
BK22-10	10	3.2	22	G1	540	74	*10808801235*
BK22-13	13	2.7	22	G1	540	74	*10808801235*
BK30-8	8	5	30	G1 1/2	650	75	11209301290
BK30-10	10	4.4	30	G1 1/2	650	75	11209301290
BK30-13	13	3.6	30	G1 1/2	650	75	11209301290
BK37-8ZG	8	6	37	G1 1/2	740	76	15309001230
BK37-10	10	5.5	37	G1 1/2	730	76	124010301435
BK37-13	13	4.6	37	G1 1/2	730	76	124010301435
BK45-8G	8	7.1	45	G1 1/2	800	78	148010301345
BK45-10	10	6.5	45	G1 1/2	820	78	124010301595
BK45-13	13	5.6	45	G1 1/2	820	78	124010301595
BK55-8G	8	10	55	G1 1/2	800	80	148010301345
BK55-10	10	8.5	55	G1 1/2	1200	80	154512001470
BK55-13	13	7.4	55	G1 1/2	1200	80	154512001470

Detailed Photos

Company Profile

FAQ

1.How do your prices compare to the manufacturer/factory?

We are the main distributor of major construction machinery manufacturers/factories in China and keep getting the best dealer prices. From the comparison and feedback from many customers, our price is even more competitive than the factory/factory price.

2.How is the delivery time?

In general, we can deliver ordinary machines immediately to our customers within 7 days, as we have various resources to inspect stock machines, locally and nationwide, and receive machines in a timely manner. But it takes more than 30 days for a manufacturer/factory to produce an order machine.

3.How often can you respond to customer inquiries?

Our team is made up of a group of hardworking and dynamic people who work around the clock to respond to customer inquiries and questions. Most issues can be successfully resolved within 8 hours, while manufacturers/factories take longer to respond.

4.Which payment methods can you accept?

Usually we can use wire transfer or letter of credit, and sometimes DP. (1) Wire transfer, 30% deposit in advance, 70% balance paid before shipment, long-term cooperation customers can present a copy of the original bill of lading. (2) Letter of credit, 100% irrevocable letter of credit without “soft terms” from internationally recognized banks can be accepted. Please seek advice from the sales manager you work with.

5.Which clauses in the Incoterms 2571 can you use?

We are a professional and mature international player and can handle all INCOTERMS 2571, we usually work on regular terms like FOB, CFR, CIF, CIP, DAP.

6.How long are your prices valid?

We are a gentle and friendly supplier, never greedy for profit. Our prices remain largely stable throughout the year. We will only adjust the price according to the following 2 situations: (1) USD exchange rate: According to the international currency exchange rate, the RMB exchange rate is quite different; (2) The manufacturer/factory adjusted the machine price due to the increase of labor cost or raw material cost.

7.What logistics methods can you use for shipping?

We can transport construction machinery with various means of transport. (1) 80% of our shipping will be by the sea, to all major continents such as Africa, South America, Middle East. (2) China’s inland neighboring countries, such as Russia, Mongolia, Kazakhstan, Kyrgyzstan, Tajikistan, Uzbekistan, Turkmenistan, etc., can transport by road or rail. (3) For urgently needed light spare parts, we can provide international express services

After-sales Service:	Warranty Service
Warranty:	1 Year
Lubrication Style:	Micro Oil
Cooling System:	Air Cooling
Power Source:	AC Power
Cylinder Position:	Vertical

Samples:	US$ 800/Piece 1 Piece(Min.Order) \| Request Sample

Customization:	Available \|

air compressor

How are air compressors used in the food and beverage industry?

Air compressors play a vital role in the food and beverage industry, providing a reliable source of compressed air for various applications. Here are some common uses of air compressors in this industry:

1. Packaging and Filling:

Air compressors are extensively used in packaging and filling operations in the food and beverage industry. Compressed air is utilized to power pneumatic systems that control the movement and operation of packaging machinery, such as filling machines, capping machines, labeling equipment, and sealing devices. The precise and controlled delivery of compressed air ensures accurate and efficient packaging of products.

2. Cleaning and Sanitization:

Air compressors are employed for cleaning and sanitization purposes in food and beverage processing facilities. Compressed air is used to operate air-powered cleaning equipment, such as air blowguns, air-operated vacuum systems, and air knives. It helps remove debris, dust, and contaminants from production lines, equipment, and hard-to-reach areas. Additionally, compressed air is used for drying surfaces after cleaning and for applying sanitizing agents.

3. Cooling and Refrigeration:

In the food and beverage industry, air compressors are utilized in cooling and refrigeration systems. Compressed air is used to drive air compressors in refrigeration units, enabling the circulation of refrigerants and maintaining optimal temperatures for food storage and preservation. The controlled airflow provided by the compressors facilitates efficient cooling and refrigeration processes.

4. Aeration and Mixing:

Air compressors are used for aeration and mixing applications in the food and beverage industry. Compressed air is introduced into processes such as fermentation, dough mixing, and wastewater treatment. It helps in promoting oxygen transfer, enhancing microbial activity, and facilitating proper mixing of ingredients or substances, contributing to the desired quality and consistency of food and beverage products.

5. Pneumatic Conveying:

In food processing plants, air compressors are employed for pneumatic conveying systems. Compressed air is used to transport bulk materials such as grains, powders, and ingredients through pipes or tubes. It enables the gentle and efficient movement of materials without the need for mechanical conveyors, reducing the risk of product damage or contamination.

6. Quality Control and Testing:

Air compressors are utilized in quality control and testing processes within the food and beverage industry. Compressed air is used for leak testing of packaging materials, containers, and seals to ensure product integrity. It is also employed for spraying air or gases during sensory analysis and flavor testing.

7. Air Agitation:

In certain food and beverage production processes, air compressors are used for air agitation. Compressed air is introduced into tanks, mixing vessels, or fermentation tanks to create turbulence and promote mixing or chemical reactions. It aids in achieving consistent product quality and uniform distribution of ingredients or additives.

It is important to note that air compressors used in the food and beverage industry must meet strict hygiene and safety standards. They may require specific filtration systems, oil-free operation, and compliance with food safety regulations to prevent contamination or product spoilage.

By utilizing air compressors effectively, the food and beverage industry can benefit from improved productivity, enhanced product quality, and efficient processing operations.

air compressor

What is the impact of altitude on air compressor performance?

The altitude at which an air compressor operates can have a significant impact on its performance. Here are the key factors affected by altitude:

1. Decreased Air Density:

As altitude increases, the air density decreases. This means there is less oxygen available per unit volume of air. Since air compressors rely on the intake of atmospheric air for compression, the reduced air density at higher altitudes can lead to a decrease in compressor performance.

2. Reduced Airflow:

The decrease in air density at higher altitudes results in reduced airflow. This can affect the cooling capacity of the compressor, as lower airflow hampers the dissipation of heat generated during compression. Inadequate cooling can lead to increased operating temperatures and potential overheating of the compressor.

3. Decreased Power Output:

Lower air density at higher altitudes also affects the power output of the compressor. The reduced oxygen content in the air can result in incomplete combustion, leading to decreased power generation. As a result, the compressor may deliver lower airflow and pressure than its rated capacity.

4. Extended Compression Cycle:

At higher altitudes, the air compressor needs to work harder to compress the thinner air. This can lead to an extended compression cycle, as the compressor may require more time to reach the desired pressure levels. The longer compression cycle can affect the overall efficiency and productivity of the compressor.

5. Pressure Adjustments:

When operating an air compressor at higher altitudes, it may be necessary to adjust the pressure settings. As the ambient air pressure decreases with altitude, the compressor’s pressure gauge may need to be recalibrated to maintain the desired pressure output. Failing to make these adjustments can result in underinflated tires, improper tool performance, or other issues.

6. Compressor Design:

Some air compressors are specifically designed to handle higher altitudes. These models may incorporate features such as larger intake filters, more robust cooling systems, and adjusted compression ratios to compensate for the reduced air density and maintain optimal performance.

7. Maintenance Considerations:

Operating an air compressor at higher altitudes may require additional maintenance and monitoring. It is important to regularly check and clean the intake filters to ensure proper airflow. Monitoring the compressor’s operating temperature and making any necessary adjustments or repairs is also crucial to prevent overheating and maintain efficient performance.

When using an air compressor at higher altitudes, it is advisable to consult the manufacturer’s guidelines and recommendations specific to altitude operations. Following these guidelines and considering the impact of altitude on air compressor performance will help ensure safe and efficient operation.

air compressor

How do oil-lubricated and oil-free air compressors differ?

Oil-lubricated and oil-free air compressors differ in terms of their lubrication systems and the presence of oil in their operation. Here are the key differences:

Oil-Lubricated Air Compressors:

1. Lubrication: Oil-lubricated air compressors use oil for lubricating the moving parts, such as pistons, cylinders, and bearings. The oil forms a protective film that reduces friction and wear, enhancing the compressor’s efficiency and lifespan.

2. Performance: Oil-lubricated compressors are known for their smooth and quiet operation. The oil lubrication helps reduce noise levels and vibration, resulting in a more comfortable working environment.

3. Maintenance: These compressors require regular oil changes and maintenance to ensure the proper functioning of the lubrication system. The oil filter may need replacement, and the oil level should be regularly checked and topped up.

4. Applications: Oil-lubricated compressors are commonly used in applications that demand high air quality and continuous operation, such as industrial settings, workshops, and manufacturing facilities.

Oil-Free Air Compressors:

1. Lubrication: Oil-free air compressors do not use oil for lubrication. Instead, they utilize alternative materials, such as specialized coatings, self-lubricating materials, or water-based lubricants, to reduce friction and wear.

2. Performance: Oil-free compressors generally have a higher airflow capacity, making them suitable for applications where a large volume of compressed air is required. However, they may produce slightly more noise and vibration compared to oil-lubricated compressors.

3. Maintenance: Oil-free compressors typically require less maintenance compared to oil-lubricated ones. They do not need regular oil changes or oil filter replacements. However, it is still important to perform routine maintenance tasks such as air filter cleaning or replacement.

4. Applications: Oil-free compressors are commonly used in applications where air quality is crucial, such as medical and dental facilities, laboratories, electronics manufacturing, and painting applications. They are also favored for portable and consumer-grade compressors.

When selecting between oil-lubricated and oil-free air compressors, consider the specific requirements of your application, including air quality, noise levels, maintenance needs, and expected usage. It’s important to follow the manufacturer’s recommendations for maintenance and lubrication to ensure the optimal performance and longevity of the air compressor.

China Custom CHINAMFG (BOREAS) Bk Series Permanent Magnet Variable Frequency Screw Air Compressor manufacturer
editor by CX 2023-10-25

China wholesaler Industrial Energy Saving Permanent Magnet Stationary Direct Driven VSD Rotary Screw Air Compressor with Good quality

Product Description

Product Description

Technical parameters of oil-free water-lubricated permanent magnet variable frequency screw compressor
HYW-G	Working pressure		Exhaust volume		Power		Noise	Air outlet pipe diameter	Net weight	Dimensions(mm)
Water lubricated series	bar	psig	(m3/min)	cfm	kW	hp	dB	Air outlet pipe diameter	kg	Length	Width	Height
HYWV-7G	7	102	0.7-1.2	24.7-42.4	7.5	10	58±3	G1″	500	1135	800	1000
	8	116	0.6-1.1	21.2-38.8	7.5	10	58±3	G1″	500	1135	800	1000
	10	145	0.5-0.9	17.7-31.8	7.5	10	58±3	G1″	500	1135	800	1000
HYWV-11G	7	102	1.0-1.6	35.3-56.5	11	15	58±3	G1″	500	1135	800	1000
	8	116	0.9-1.5	31.8-53	11	15	58±3	G1″	500	1135	800	1000
	10	145	0.7-1.3	24.7-45.9	11	15	58±3	G1″	500	1135	800	1000
HYWV-15G	7	102	1.1-2	38.8-71	15	20	60±3	G1″	550	1400	1000	1200
	8	116	1-1.9	35.4-67.3	15	20	60±3	G1″	550	1400	1000	1200
	10	145	/	/	15	20	60±3	G1″	550	1400	1000	1200
HYWV-15G	7	102	/	/	15	20	60±3	G1″	550	1170	900	1100
	8	116	/	/	15	20	60±3	G1″	550	1170	900	1100
	10	145	0.9-1.6	31.8-56.6	15	20	60±3	G1″	550	1170	900	1100
HYWV-18.5G	7	102	1.8-3.1	63.6-109.5	18.5	25	61 ±3	G1″	600	1400	1000	1200
	8	116	1.6-2.8	56.5-98.9	18.5	25	61 ±3	G1″	600	1400	1000	1200
	10	145	1.5-2.5	53-88.3	18.5	25	61±3	G1″	600	1400	1000	1200
HYWV-22G	7	102	2.2-3.7	77.7-130.7	22	30	61 ±3	G1″	655	1400	1000	1200
	8	116	2.0-3.4	70.6-120.1	22	30	61 ±3	G1″	655	1400	1000	1200
	10	145	1.8-3.0	63.6-105.9	22	30	61 ±3	G1″	655	1400	1000	1200
HYWV-30G	7	102	3.1-5.2	109.5-183.6	30	40	64±3	G11/2″	1150	1920	1170	1320
	8	116	2.8-4.7	98.9-166	30	40	64±3	G11/2″	1150	1920	1170	1320
	10	145	2.5-4.3	88.3-151.9	30	40	64±3	G11/2″	1150	1920	1170	1320
HYWV-37G	7	102	3.6-6.1	127.1-215.4	37	50	64±3	G11/2″	1200	1920	1170	1320
	8	116	3.3-5.6	116.5-197.8	37	50	64±3	G11/2″	1200	1920	1170	1320
	10	145	3.0-5.0	105.9-176.6	37	50	64±3	G11/2″	1200	1920	1170	1320
HYWV-45G	7	102	4.5-7.5	158.9-264.9	45	60	66±3	G11/2″	1320	1920	1170	1320
	8	116	4.0-6.8	141.3-240.1	45	60	66±3	G11/2″	1320	1920	1170	1320
	10	145	3.6-6.0	127.1-211.9	45	60	66±3	G11/2″	1320	1920	1170	1320
HYWV-55G	7	102	6.0-10.0	211.9-353.1	55	75	66±3	DN50	1520	1930	1320	1535
	8	116	5.4-9.0	191-317.8	55	75	66±3	DN50	1520	1930	1320	1535
	10	145	4.6-7.8	162.4-275.5	55	75	66±3	DN50	1520	1930	1320	1535
HYWV-75G	7	102	7.8-13.0	275.5-459.1	75	100	70±3	DN50	1620	1930	1320	1535
	8	116	7.2-12.0	254.3-423.8	75	100	70±3	DN50	1620	1930	1320	1535
	10	145	6.0-10.0	211.9-353.1	75	100	70±3	DN50	1620	1930	1320	1535
HYWV-90G	7	102	9.3-15.5	328.4-547.4	90	120	70±3	DN50	1800	1930	1320	1535
	8	116	8.4-14.0	296.6-494.4	90	120	70±3	DN50	1800	1930	1320	1535
	10	145	7.5-12.5	264.9-414	90	120	70±3	DN50	1800	1930	1320	1535
HYWV-110G	7	102	12.0-20.0	423.8-706.3	110	150	72±3	DN80	3100	2300	1600	1750
	8	116	10.8-18.0	381.4-635.7	110	150	72±3	DN80	3100	2300	1600	1750
	10	145	9.6-16.0	339-565	110	150	72±3	DN80	3100	2300	1600	1750
HYWV-132G	7	102	15.0-25.0	527.9-882.9	132	175	72±3	DN80	3250	2300	1600	1750
	8	116	13.8-23.0	487.3-812.2	132	175	72±3	DN80	3250	2300	1600	1750
	10	145	12.0-20.0	423.8-706.3	132	175	72±3	DN80	3250	2300	1600	1750
HYWV-160G	7	102	16.2-27.0	572.1-953.5	160	215	72±3	DN100	4500	2860	1600	1800
	8	116	15.3-25.5	540.3-900.5	160	215	72±3	DN100	4500	2860	1600	1800
	10	145	14.4-24.0	508.5-847.6	160	215	72±3	DN100	4500	2860	1600	1800
HYWV-185G	7	102	18.0-30.0	635.7-1059.4	185	250	74±3	DN100	4500	2860	1600	1800
	8	116	16.8-28.0	593.3-988.8	185	250	74±3	DN100	4500	2860	1600	1800
	10	145	15.0-25.0	529.7-882.9	185	250	74±3	DN100	4500	2860	1600	1800
HYWV-200G	7	102	21.6-36.0	762.8-1271.3	200	270	74±3	DN125	4800	3150	1850	2050
	8	116	19.8-33.0	699.2-1165.4	200	270	74±3	DN125	4800	3150	1850	2050
	10	145	16.2-27.0	572.1-953.5	200	270	74±3	DN125	4800	3150	1850	2050
HYWV-250G	7	102	25.8-43.0	911.1-1518.5	250	350	74±3	DN125	5200	3150	1850	2050
	8	116	24.6-41.0	868.7-1447.9	250	350	74±3	DN125	5200	3150	1850	2050
	10	145	22.8-38.0	805.2-1342	250	350	74±3	DN125	5200	3150	1850	2050

Cooling method: (Air cooling:HYWV-7G~HYWV-45G),(Water cooling:HYWV-55G~HYWV-250G))

Display

The advantage of screw air compressor

Company strength display

HangZhou CHINAMFG Gas Equipment Co., Ltd. is a manufacturer engaged in the research and development, design and production of gas compressors. The company has its own production technology, processing equipment and assembly technology, and has many years of experience in the production of various flammable and explosive special gas compressors.

Huayan compressor products cover almost all gas media, up to 6th-stage compression and 3000kw power. Products can be customized according to customer requirements to better meet customer needs. The products are mainly used in gas compressors in the petroleum industry, chemical and natural gas compressors, industrial compressors, compressors for waste gas treatment and biogas utilization, and compressors for special gases.

After Sales Service
1.Quick response within 2 to 8 hours, with a reaction rate exceeding 98%;
2. 24-hour telephone service, please feel free to contact us;
3. The whole machine is guaranteed for 1 year (excluding pipelines and human factors);
4. Provide consulting service for the service life of the whole machine, and provide 24-hour technical support via email;
5. On-site installation and commissioning by our experienced technicians;

Exhibition Display

Certificate display
Packaging and Shipping

FAQ

Q1: What is the rotor speed for the air end?
A1: 2980rmp.

Q2: What’s your lead time?
A2: usually, 5-7 days. (OEM orders: 15days)

Q3: Can you offer water cooled air compressor?
A3: Yes, we can (normally, air cooled type).

Q4: What’s the payment term?
A4: T/T, L/C, Western Union, etc. Also we could accept USD, RMB, and other currency.

Q5: Do you accept customized voltage?
A5: Yes. 380V/50Hz/3ph, 380V/60Hz/3ph, 220V/50Hz/3ph, 220V/60Hz/3ph, 440V/50Hz/3ph, 440V/60Hz/3ph, or as per your requests.

Q6: What is your warranty for air compressor?
A6: One year for the whole air compressor(not including the consumption spare parts) and technical supports can be provided according to your needs.

Q7: Can you accept OEM orders?
A7: Yes, OEM orders are warmly welcome.

Q8: How about your customer service and after-sales service?
A8: 24hrs on-line support, 48hrs problem solved promise.

Q9: Do you have spare parts in stock?
A9: Yes, we do.

Q10: What kind of initial lubrication oil you used in air compressor?
A10: TOTAL 46# mineral oil.

Lubrication Style:	Oil-free
Cooling System:	Air Cooling
Cylinder Position:	Vertical
Structure Type:	Closed Type
Installation Type:	Movable Type
Type:	Single Screw Compressor

Customization:	Available \|

air compressor

How are air compressors employed in the petrochemical industry?

1. Instrumentation and Control Systems:

2. Pneumatic Tools and Equipment:

3. Process Air and Gas Supply:

4. Cooling and Ventilation:

5. Nitrogen Generation:

6. Instrument Air:

air compressor

Can air compressors be used for medical and dental applications?

Yes, air compressors can be used for various medical and dental applications. Compressed air is a reliable and versatile utility in healthcare settings, providing power for numerous devices and procedures. Here are some common applications of air compressors in medical and dental fields:

1. Dental Tools:

Air compressors power a wide range of dental tools and equipment, such as dental handpieces, air syringes, air scalers, and air abrasion devices. These tools rely on compressed air to generate the necessary force and airflow for effective dental procedures.

2. Medical Devices:

Compressed air is used in various medical devices and equipment. For example, ventilators and anesthesia machines utilize compressed air to deliver oxygen and other gases to patients. Nebulizers, used for respiratory treatments, also rely on compressed air to convert liquid medications into a fine mist for inhalation.

3. Laboratory Applications:

Air compressors are used in medical and dental laboratories for various purposes. They power laboratory instruments, such as air-driven centrifuges and sample preparation equipment. Compressed air is also used for pneumatic controls and automation systems in lab equipment.

4. Surgical Tools:

In surgical settings, compressed air is employed to power specialized surgical tools. High-speed air-driven surgical drills, saws, and bone-cutting instruments are commonly used in orthopedic and maxillofacial procedures. Compressed air ensures precise control and efficiency during surgical interventions.

5. Sterilization and Autoclaves:

Compressed air is essential for operating sterilization equipment and autoclaves. Autoclaves use steam generated by compressed air to sterilize medical instruments, equipment, and supplies. The pressurized steam provides effective disinfection and ensures compliance with rigorous hygiene standards.

6. Dental Air Compressors:

Specialized dental air compressors are designed specifically for dental applications. These compressors have features such as moisture separators, filters, and noise reduction mechanisms to meet the specific requirements of dental practices.

7. Air Quality Standards:

In medical and dental applications, maintaining air quality is crucial. Compressed air used in healthcare settings must meet specific purity standards. This often requires the use of air treatment systems, such as filters, dryers, and condensate management, to ensure the removal of contaminants and moisture.

8. Compliance and Regulations:

Medical and dental facilities must comply with applicable regulations and guidelines regarding the use of compressed air. These regulations may include requirements for air quality, maintenance and testing procedures, and documentation of system performance.

It is important to note that medical and dental applications have specific requirements and standards. Therefore, it is essential to choose air compressors and associated equipment that meet the necessary specifications and comply with industry regulations.

air compressor

What is the impact of tank size on air compressor performance?

The tank size of an air compressor plays a significant role in its performance and functionality. Here are the key impacts of tank size:

1. Air Storage Capacity: The primary function of the air compressor tank is to store compressed air. A larger tank size allows for greater air storage capacity. This means the compressor can build up a reserve of compressed air, which can be useful for applications that require intermittent or fluctuating air demand. Having a larger tank ensures a steady supply of compressed air during peak usage periods.

2. Run Time: The tank size affects the run time of the air compressor. A larger tank can provide longer continuous operation before the compressor motor needs to restart. This is because the compressed air in the tank can be used to meet the demand without the need for the compressor to run continuously. It reduces the frequency of motor cycling, which can improve energy efficiency and prolong the motor’s lifespan.

3. Pressure Stability: A larger tank helps maintain stable pressure during usage. When the compressor is running, it fills the tank until it reaches a specified pressure level, known as the cut-out pressure. As the air is consumed from the tank, the pressure drops to a certain level, known as the cut-in pressure, at which point the compressor restarts to refill the tank. A larger tank size results in a slower pressure drop during usage, ensuring more consistent and stable pressure for the connected tools or equipment.

4. Duty Cycle: The duty cycle refers to the amount of time an air compressor can operate within a given time period. A larger tank size can increase the duty cycle of the compressor. The compressor can run for longer periods before reaching its duty cycle limit, reducing the risk of overheating and improving overall performance.

5. Tool Compatibility: The tank size can also impact the compatibility with certain tools or equipment. Some tools, such as high-demand pneumatic tools or spray guns, require a continuous and adequate supply of compressed air. A larger tank size ensures that the compressor can meet the air demands of such tools without causing pressure drops or affecting performance.

It is important to note that while a larger tank size offers advantages in terms of air storage and performance, it also results in a larger and heavier compressor unit. Consider the intended application, available space, and portability requirements when selecting an air compressor with the appropriate tank size.

Ultimately, the optimal tank size for an air compressor depends on the specific needs of the user and the intended application. Assess the air requirements, duty cycle, and desired performance to determine the most suitable tank size for your air compressor.

China wholesaler Industrial Energy Saving Permanent Magnet Stationary Direct Driven VSD Rotary Screw Air Compressor with Good quality
editor by CX 2023-10-19

China Custom 75sfet-5.5 Two-Stage Compression Permanent Magnet Frequency Conversion Screw Air Compressor for Textile Industry air compressor price

Product Description

75SFeT-5.5 Two-stage compression Permanent Magnet Frequency Conversion Screw Air compressor For Textile Industry

Product Description

In the textile industry, the pressure requirements of the air jet looms for compressed gas are generally in the range of 4.5 bar to 5.5 bar. The conventional compressor selection and use method is to use the compressor with a rated pressure of 7 bar or 8 bar to reduce pressure. Compression caused waste of energy and increased manufacturing costs. Adhering to the concept of energy saving and environmental protection, Green Earth, we designed and developed a two-stage compression energy-saving CHINAMFG for textile and a two-stage compression permanent magnet frequency conversion energy-saving screw compressor.

Applications

Construction engineering, mine, water well drilling, etc

Company Information

ABT Drilling Equipment Co., Ltd. mainly provides holistic drilling solutions, serving the mining, stone crushing, water conservancy drilling industry, to help you solve the problem of drilling at high efficiency and low cost. We mainly provide mobile air compressors, drilling rigs, hammer, drill bit, crushers, underground water detector.We are your trustworthy partner.

Lubrication Style:	Lubricated
Cooling System:	Air Cooling
Power Source:	AC Power

Customization:	Available \|

.shipping-cost-tm .tm-status-off{background: none;padding:0;color: #1470cc}

Shipping Cost: Estimated freight per unit.	about shipping cost and estimated delivery time.

Payment Method:
	Initial Payment Full Payment

Currency:	US$

Return&refunds:	You can apply for a refund up to 30 days after receipt of the products.

air compressor

Are there special considerations for air compressor installations in remote areas?

Yes, there are several special considerations to take into account when installing air compressors in remote areas. These areas often lack access to infrastructure and services readily available in urban or well-developed regions. Here are some key considerations:

1. Power Source:

Remote areas may have limited or unreliable access to electricity. It is crucial to assess the availability and reliability of the power source for operating the air compressor. In some cases, alternative power sources such as diesel generators or solar panels may need to be considered to ensure a consistent and uninterrupted power supply.

2. Environmental Conditions:

Remote areas can present harsh environmental conditions that can impact the performance and durability of air compressors. Extreme temperatures, high humidity, dust, and corrosive environments may require the selection of air compressors specifically designed to withstand these conditions. Adequate protection, insulation, and ventilation must be considered to prevent damage and ensure optimal operation.

3. Accessibility and Transport:

Transporting air compressors to remote areas may pose logistical challenges. The size, weight, and portability of the equipment should be evaluated to ensure it can be transported efficiently to the installation site. Additionally, the availability of suitable transportation infrastructure, such as roads or air transportation, needs to be considered to facilitate the delivery and installation process.

4. Maintenance and Service:

In remote areas, access to maintenance and service providers may be limited. It is important to consider the availability of trained technicians and spare parts for the specific air compressor model. Adequate planning for routine maintenance, repairs, and troubleshooting should be in place to minimize downtime and ensure the longevity of the equipment.

5. Fuel and Lubricants:

For air compressors that require fuel or lubricants, ensuring a consistent and reliable supply can be challenging in remote areas. It is necessary to assess the availability and accessibility of fuel or lubricant sources and plan for their storage and replenishment. In some cases, alternative or renewable fuel options may need to be considered.

6. Noise and Environmental Impact:

Remote areas are often characterized by their natural beauty and tranquility. Minimizing noise levels and environmental impact should be a consideration when installing air compressors. Selecting models with low noise emissions and implementing appropriate noise reduction measures can help mitigate disturbances to the surrounding environment and wildlife.

7. Communication and Remote Monitoring:

Given the remote location, establishing reliable communication channels and remote monitoring capabilities can be essential for effective operation and maintenance. Remote monitoring systems can provide real-time data on the performance and status of the air compressor, enabling proactive maintenance and troubleshooting.

By addressing these special considerations, air compressor installations in remote areas can be optimized for reliable operation, efficiency, and longevity.

air compressor

How does the horsepower of an air compressor affect its capabilities?

The horsepower of an air compressor is a crucial factor that directly impacts its capabilities and performance. Here’s a closer look at how the horsepower rating affects an air compressor:

Power Output:

The horsepower rating of an air compressor indicates its power output or the rate at which it can perform work. Generally, a higher horsepower rating translates to a greater power output, allowing the air compressor to deliver more compressed air per unit of time. This increased power output enables the compressor to operate pneumatic tools and equipment that require higher air pressure or greater airflow.

Air Pressure:

The horsepower of an air compressor is directly related to the air pressure it can generate. Air compressors with higher horsepower ratings have the capacity to produce higher air pressures. This is particularly important when operating tools or machinery that require specific air pressure levels to function optimally. For example, heavy-duty pneumatic tools like jackhammers or impact wrenches may require higher air pressure to deliver the necessary force.

Air Volume:

In addition to air pressure, the horsepower of an air compressor also affects the air volume or airflow it can provide. Higher horsepower compressors can deliver greater volumes of compressed air, measured in cubic feet per minute (CFM). This increased airflow is beneficial when using pneumatic tools that require a continuous supply of compressed air, such as paint sprayers or sandblasters.

Duty Cycle:

The horsepower rating of an air compressor can also influence its duty cycle. The duty cycle refers to the amount of time an air compressor can operate continuously before it needs to rest and cool down. Higher horsepower compressors often have larger and more robust components, allowing them to handle heavier workloads and operate for longer periods without overheating. This is particularly important in demanding applications where continuous and uninterrupted operation is required.

Size and Portability:

It’s worth noting that the horsepower rating can also affect the physical size and portability of an air compressor. Higher horsepower compressors tend to be larger and heavier due to the need for more substantial motors and components to generate the increased power output. This can impact the ease of transportation and maneuverability, especially in portable or mobile applications.

When selecting an air compressor, it is essential to consider the specific requirements of your intended applications. Factors such as desired air pressure, airflow, duty cycle, and portability should be taken into account. It’s important to choose an air compressor with a horsepower rating that aligns with the demands of the tools and equipment you plan to operate, ensuring optimal performance and efficiency.

Consulting the manufacturer’s specifications and guidelines can provide valuable information on how the horsepower rating of an air compressor corresponds to its capabilities and suitability for different tasks.

air compressor

How do oil-lubricated and oil-free air compressors differ?

Oil-lubricated and oil-free air compressors differ in terms of their lubrication systems and the presence of oil in their operation. Here are the key differences:

Oil-Lubricated Air Compressors:

Oil-Free Air Compressors:

China Custom 75sfet-5.5 Two-Stage Compression Permanent Magnet Frequency Conversion Screw Air Compressor for Textile Industry air compressor price
editor by CX 2023-10-19